- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- suggestions for a new tape drive on HP 9000 D220 s...
StoreEver Tape Storage
1753668
Members
5474
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2002 11:21 AM
тАО09-28-2002 11:21 AM
Hello. I have a HP 9000 D220 server w/the original DDS1 internal tape drive. I need to purchase a larger tape drive, I don't want a DAT, I'm looking for a HP DLT solution. Can you recommend a drive, internal or external, that's proven to work on the D220? Thanks!
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2002 03:50 PM
тАО09-28-2002 03:50 PM
Solution
Grant: you're primary gating factor nowadays for D-class external tapes or libraries will be, "can I get it with HVD/FWD SCSI?"
Most modern drives are LVD SCSI, which D-class doesn't have and never will have. I would suggest that you get a refurbished "Smart Storage" DLT8000 drive from HP. Contact your sales rep, HVD DLT8000 drives and libraries may be available new, or from HP refurbished division. If you know exactly what you want, you might even work with a used equipment broker (be careful, and check references, and get a warranty).
One other possibility is to use the SE SCSI bus on your D-class server to run a DLT vs80 drive. See:
http://www.hp.com/products1/storage/products/tapebackup/dlt_tapedrives/dltvs80_drives/index.html
Devices that use LVD UltraSCSI can also run on the older Single-Ended SCSI voltage levels. They automatically sense SE signals and switch to that mode. DLT vs80 drives can hold 40GB native, like DLT8000s, but run slower. They are vastly faster than a DDS DAT. They use the standard DLT "Data IV" cartridge (cheap, these days).
What you will find is that this is not a "supported configuration", according to the list. D- and K- class aren't even listed, since they went obsolete before this drive came along. All the "supported" servers use LVD SCSI, not SE, so... it would need a trial on your part to attempt this. Many things will work that aren't officially "supported", but if you went with a new DLT vs80 drive, you would want to be sure you could return it if you can't make it work on the SE bus (drivers, etc).
To connect the DLT vs80 to the SE port on the D220, you would need a HDTS50 (50-pin mini-D connector) to HDTS68 (68-pin mini-D) male-to-male cable. Also, the drive can be free-standing or rack-mount, which you have to decide (may affect cable length) SE SCSI is limited to 21 feet, so 2-5 meter cables are normally used. You will also need a 68-pin terminator, but a "multimode" LVD/SE terminator should come with the drive (double-check).
You will have the "rack/free standing" choice with HP refurb gear, if that's the way you decide to go. If you use HP refurb HVD/FWD DLT8000, you will also need a FWD card for your D-class (requires an HSC slot, so check the back of your computer), and an HDTS68 to HDTS68 male-to-male cable.
Good Luck with this, hopefully I have given you somewhere to start.
--bmr
Most modern drives are LVD SCSI, which D-class doesn't have and never will have. I would suggest that you get a refurbished "Smart Storage" DLT8000 drive from HP. Contact your sales rep, HVD DLT8000 drives and libraries may be available new, or from HP refurbished division. If you know exactly what you want, you might even work with a used equipment broker (be careful, and check references, and get a warranty).
One other possibility is to use the SE SCSI bus on your D-class server to run a DLT vs80 drive. See:
http://www.hp.com/products1/storage/products/tapebackup/dlt_tapedrives/dltvs80_drives/index.html
Devices that use LVD UltraSCSI can also run on the older Single-Ended SCSI voltage levels. They automatically sense SE signals and switch to that mode. DLT vs80 drives can hold 40GB native, like DLT8000s, but run slower. They are vastly faster than a DDS DAT. They use the standard DLT "Data IV" cartridge (cheap, these days).
What you will find is that this is not a "supported configuration", according to the list. D- and K- class aren't even listed, since they went obsolete before this drive came along. All the "supported" servers use LVD SCSI, not SE, so... it would need a trial on your part to attempt this. Many things will work that aren't officially "supported", but if you went with a new DLT vs80 drive, you would want to be sure you could return it if you can't make it work on the SE bus (drivers, etc).
To connect the DLT vs80 to the SE port on the D220, you would need a HDTS50 (50-pin mini-D connector) to HDTS68 (68-pin mini-D) male-to-male cable. Also, the drive can be free-standing or rack-mount, which you have to decide (may affect cable length) SE SCSI is limited to 21 feet, so 2-5 meter cables are normally used. You will also need a 68-pin terminator, but a "multimode" LVD/SE terminator should come with the drive (double-check).
You will have the "rack/free standing" choice with HP refurb gear, if that's the way you decide to go. If you use HP refurb HVD/FWD DLT8000, you will also need a FWD card for your D-class (requires an HSC slot, so check the back of your computer), and an HDTS68 to HDTS68 male-to-male cable.
Good Luck with this, hopefully I have given you somewhere to start.
--bmr
We must indeed all hang together, or, most assuredly, we shall all hang separately. (Benjamin Franklin)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-29-2002 05:09 AM
тАО09-29-2002 05:09 AM
Re: suggestions for a new tape drive on HP 9000 D220 server
Thank you for taking the time to reply. Your explanation was great. I've decided to go w/a DDS Dat40i. I've already got 2 others for other non-HP servers and have reviewed the documentation. The docs say you can plug them into SE SCSI cables w/no problem, only need to purchase the HP 68-50 adapter cable. This is what I'll do. BUT, I still have the issue of termination as a problem. The drive won't come w/a cable or multimode terminator for an internal drive. I have everything I need for cabling except the terminator. I'm wondering if I can terminate the drive itself w/o an external multimode terminator. I don't think so, but I'll check. What do you think about the termination issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2002 10:11 AM
тАО09-30-2002 10:11 AM
Re: suggestions for a new tape drive on HP 9000 D220 server
Grant: To connect up an external DAT40 on the SE bus, you will need to come up with a terminator that is 68 pin, since your existing terminator is 50 pin. A 68 pin terminator should come with any "deskside" drive, but if you need one, just go buy one at a local computer supply place. All LVD/SE terminators are interchangeable, provided that they say LVD/SE or something like that, and that you have the right plug type (HDTS68, not VHDCI68, which is the super-mini LVD plugs).
If needed, you can get LVD/SE cables and terminators on the internet or via mail-order catalogs. You know what you need, so that should not be difficult to do.
Mind the SCSI ID, since the existing DAT will still be on the bus. You only have 7 SCSI IDs on this old bus, but you should still be well within those bounds.
I wouldn't suggest replacing the existing DAT drive with the DAT40, since the shape and size (50 vs 68 pins) of the internal connector won't match. An adapter cable would be all you'd require, and they do exist, but they are harder to find than external cables.
Regards, --bmr
If needed, you can get LVD/SE cables and terminators on the internet or via mail-order catalogs. You know what you need, so that should not be difficult to do.
Mind the SCSI ID, since the existing DAT will still be on the bus. You only have 7 SCSI IDs on this old bus, but you should still be well within those bounds.
I wouldn't suggest replacing the existing DAT drive with the DAT40, since the shape and size (50 vs 68 pins) of the internal connector won't match. An adapter cable would be all you'd require, and they do exist, but they are harder to find than external cables.
Regards, --bmr
We must indeed all hang together, or, most assuredly, we shall all hang separately. (Benjamin Franklin)
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP