- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- StoreVirtual Storage
- >
- Re: Comments/Opinions on upgrading to v10?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-19-2013 08:35 PM - edited 01-19-2013 08:37 PM
01-19-2013 08:35 PM - edited 01-19-2013 08:37 PM
Re: Comments/Opinions on upgrading to v10?
Had anyone success in upgrading a VSA on Hyper-V?
We have 3 nodes and a FOM, 2 of them are within VMWare, and 1 on Hyper-V.
Setup seems to stall on Hyper-V with Initialisation. It seems nothing was partly upgraded, but it stopps us upgrading the management group.
Could it be a memory issue?
I figured too late, that the new requirements for 1,5 TB is 3 GB, which was 1 GB earlier.
But nethertheless, even on VMWare with 1 GB RAM and 1,5 TB it could initialize the setup.
I changed it to 1,5 GB RAM and no change. We will have to get more ram on that server first and then try it with 3 GB. But somehow I doubt this is the reason, as checks don't warn you, aswell as it was only the init, which worked fine on VMware.
Last message always was:
Received an UpgradeScriptStatus message from the install server running on the node It was : platform configuration: '/mnt/lhnupgrade/platforms/HVNSM.sh' ...
Thanks
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2013 06:26 AM
01-20-2013 06:26 AM
Re: Comments/Opinions on upgrading to v10?
I upgraded hyper-v VSAs "without" issue. The upgrade process stalled for me while the CMC said it was waiting for node. Turned out the default gateway was reset and I had to manually open the VSA's console and reset the IP information for the node. Once reset and rebooted everything continued along just fine. This was supposed to be fixed in the latest v10 patch.
Are you really memory strapped? I thought the suggestion was something like 4GB. I know they upped the reccomendation with v10, but I can't remember what it is.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2013 08:17 AM
01-20-2013 08:17 AM
Re: Comments/Opinions on upgrading to v10?
Hi, ok good to hear. I checked the issue with the gateway but that was there. So you mean rebooting the node during the setup hangs could help?
Didn't to lot of updates with Lefthands so far, as we have our P4500 on Main Site, and VSA on our local site only since May last year, and those updates still scare me, especially when something hangs. After the 60 minute timeout I rebooted all nodes and nothing was installed. At the moment I just want to update our local site.
So the only assumption is still RAM (even that VMWare didn't have the problem), we will go for recommended settings. And probably as it goes through our firewall into the ISCSI LAN, that the session expires and CMC doesn't pick it up again? We noticed disconnections to our VSA's from CMC pretty quick, which is a result of shorter session time outs. Haven't thought of that earlier. Might be Hyper-V takes longer to answer as VMWare...
What I wonder at memory is: "At least this much memory", what's the advantage of more memory, as it's not used for caching?
About memory, this is what they say in the guide
Table 4 Memory requirements for VSA for Hyper-V disks
Total capacity of all installed disks Requires at least this much memory
5 GB to 500 GB 3 GB
500 GB to 5 TB 4 GB
5 TB to 10 TB 5 GB
Thanks
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2013 04:02 PM - edited 01-21-2013 04:04 PM
01-21-2013 04:02 PM - edited 01-21-2013 04:04 PM
Re: Comments/Opinions on upgrading to v10?
Patrick,
I have the same problem as you. I have a support ticket, in, but at the moment guys at HP don't see anything in the logs. It has gone to engineering, so I don't expect a fix for a while. My nodes all have 6GB of memory and 3.5 TB of storage, running on esxi 5.1.
I also tried the latest update with my laptop on the same subnet to see if my issue was due to the gateway problem, and it still didn't upgrade. Maybe it won't ever upgrade now that it is broken.
Thinking I might just rebuild it on 10.
Dan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-05-2013 01:46 PM
02-05-2013 01:46 PM
Re: Comments/Opinions on upgrading to v10?
Hi,
did you get this issue solved?
Did it also stop at the first node or done more than that?
I haven't retried yet as we wanted to be sure having enough ram before doing so.
But any updated info would be useful so I know if I should prepare needing support ;)
Thanks
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-11-2013 03:27 PM
02-11-2013 03:27 PM
Re: Comments/Opinions on upgrading to v10?
Originally when I tried upgrading to 10.0.00.1888 and it failed on node 4, and 5 out of the 5 nodes that I have.
I was about to rebuild ours on version 10, but I thought I would give the udpate another try after they released version 10.0.00.1896. And it worked, but I did have to reboot node 4 and 5 to clear out the unfinished upgrade from the upgrade partition.
Dan.
- « Previous
-
- 1
- 2
- Next »