- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- StoreVirtual Storage
- >
- Re: P4500 Storage Array
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2011 07:42 AM
07-26-2011 07:42 AM
P4500 Storage Array
We have a couple of incidents regarding the P4500 Storage array, where the SA seems to loose its own OS. (We are using SAN IQ V 9)
The SA will boot to the DHCP screen, and then restart again.
We have completed a Quick System Restore successfully, however upon re-configuration of the two on board NICS one of which will not work. If we configure the first NIC thereafter the IP responds correctly but as soon as the second NIC is configured, both IP's will not work (they are on the same subnet.
Is there a problem with my SAN IQ, am I mis-configuring and why does the SA loose its own OS.
All system boards, backplane and memory have also checked and re-seated as per the H/desk At HP.
Many Thanks
dave
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2011 10:55 AM
07-26-2011 10:55 AM
Re: P4500 Storage Array
Certainly sounds like a hardware issue on surface. What do you mean when you say "SA seems to loose its own OS" ? Also, you should only configure the first NIC and then make a bond between the two NICs. You however should not loose connectivity even if you have two NIC active outside of a bond. You also want to check if you have the right NIC configured as SANiQ interface and storage system discovered properly via that interface.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2011 12:34 PM
07-26-2011 12:34 PM
Re: P4500 Storage Array
Move it to a different Slot on the Raiser Card.
This I think should solve the issue with booting to OS.
Regarding 2nd issue, check connecting the nic 2 only..
Try nic 2 on the working switch (which was connected to nic1)
Try ... isolating the issue..
--------------------------------------------------------------
How to assign points? Click the KUDOS! star!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2011 01:36 AM
07-27-2011 01:36 AM
Re: P4500 Storage Array
Hi ajamil786. When you start the SA I believe that the SA boots to its own "cut down linux OS" giving you a network CFG menu,so you can configure your NICS and Speed(my terminology maybe incorrect). Within the menu I would configure each NIC witha seperate IP address. re-start the SA
Then connect using the CMC I would then make the Network Bond between NICS.
So are you saying we chould only configure one of the NICS with an IP and then Bond NIC2 thereafter, usually after a quick restore the second NIC is set to "DISABLE". Do you configure to DHCP?
Thanks for your reply.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2011 01:43 AM
07-27-2011 01:43 AM
Re: P4500 Storage Array
Jitun,
We found if we change the Default G/way address( Nic 2) the Network services restart and it clears the issue. Is there any other way of Restarting the network services manually??
I will double check the Raid controller card.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2011 01:54 AM
07-27-2011 01:54 AM
Re: P4500 Storage Array
We have just only configured one IP to the first NIC and have bonded sucessfully to the second NIC within the CMC.
We'll test the re-seat of the Raid Controller.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2011 03:38 AM
07-27-2011 03:38 AM
Re: P4500 Storage Array
Update...
I have re-seated the Riser card as suggested and re-powered on still working OK at this point. Then I relised I'd left the Plastic Airflow off, so powered off and put back in...Powered ON, guess what it won't boot it needs another Quick restore... I think its looking like hardware on this particular issue. Cheers