Procurve 2848 Vlan Routing

[Anakonda]

From time to time we'r testing some applications which are webbased.

I would like to configure our Procurve 2848 configure(for example port 27 as vlan) and make a route between this port and our network.

it's actualy a separate network

Original Network on Default vlan:
192.168.1.0 255.255.255.0

default gateway: 192.168.1.1

Test network on vlan 2 port 27:
192.168.2.1 255.255.255.0

Q1: How to assign a IP address to this vlan port.

Q2: How to route this port to default vlan.


all machines on vlan 2 on port 27 must be able to access internet.


Rene

[cenk sasmaztin]

hi Rane

I make config for your test

yess..

primary setup on switch enable ip routing

whit this command

config)#ip routing

and assign ip address vlan 1

config-vlan1)#ip address 192.168.1.1/24

and you can create new vlan 2

config)#vlan 2

and assign ip address

config-vlan2)#ip address 192.168.2.1/24

after assign vlan 2 member port on switch (all port default member vlan 1)

for example interface 27

config-vlan2)#untagged 27

and write static routig command on switch for internet connection

0.0.0.0 0.0.0.0 192.168.1.10 (1.10 ip internet router lan ip )

and you can must be write on internet router static ip command

192.168.1.0 255.255.255.0 192.168.1.1
192.168.2.0 255.255.255.0 192.168.1.1

ok..... at the present time connect pc on switch

pc 1 vlan1 member pc

ip address 192.168.1.20
subnet mask 255.255.255.0
default gateway 192.168.1.1


pc 2 vlan 2 member pc

ip address 192.168.2.20
subnet mask 255.255.255.0
default gateway 192.168.2.1

good luck

[Anakonda]

Thanks for your quick responce.

The switch is already configured.

All ports are member of default vlan.

i have configured port 27 throug hp management tool as vlan 2. without ip address.

now i can't delete this port anymore.

First i need to aasign a ip address to this port.
Then i need to make the route between these two vlan's.

[cenk sasmaztin]

Hi rene

fristly
you can create vlan 2 on switch and assign ip address vlan 2

192.168.2.1/24

and you can must be int 27 untagged member vlan 2

imposible assign ip address on port
ip address assign on vlan interface

[Anakonda]

when i try to set ip addres i receive the message that the ip address exists.

How can i check that.

Thanks for your support

[Anakonda]

Ok,

I have now the following configured:

Default_Vlan: 192.168.1.10
Vlan 2: 192.168.2.1

Default gateway for both vlan's is : 192.168.1.1

Ip route is enabled.

So far so good.

But how can i access Default_vlan and internet?

[cenk sasmaztin]

please look attach file

[Anakonda]

Thanks for the attached file.

Now i can ping other pc's, but the pc's on the send vlan can not internet.

These are the results of my sho ip:

VLAN: VLAN_2
IP CONFIG: Manual
IP ADDRESS: 192.168.2.10
SUBNET MASK: 255.255.0.0
PROXY ARP: NO

[cenk sasmaztin]

All the same ...

change your ip address my configuration
and you make test

cenk

[cenk sasmaztin]

sory soryy

please send me sh run print now