- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: 2650 cli output hang
Switches, Hubs, and Modems
1748198
Members
2606
Online
108759
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2008 01:28 AM
тАО12-05-2008 01:28 AM
2650 cli output hang
Hi everyone
I got a problem with a HP 2650, J4899C, switch running H10.67
When trying to issue a command like 'show interface' through telnet or SSH I get a list of interface from 1 to 19, but half the line of interface 20 is shown and I have to kill the session and start over again. If I specify the port number, like 'show interface 20' I got no problem. I have tested this on all interfaces.
I get a similar error when running 'show vlan 101' or even when listing the menu.
Also, I am not able to get up the web interface......
But some of the commands, like 'show running' is working just fine.
The switch is in another building, connected through a wireless bridge. The clients are connected to the network, and are working properly.
The only problem for me is being able to manage the switch in a proper way, and I am afraid there is something really wrong....
I attach the config from the device.
Best regards
.:Rune:.
I got a problem with a HP 2650, J4899C, switch running H10.67
When trying to issue a command like 'show interface' through telnet or SSH I get a list of interface from 1 to 19, but half the line of interface 20 is shown and I have to kill the session and start over again. If I specify the port number, like 'show interface 20' I got no problem. I have tested this on all interfaces.
I get a similar error when running 'show vlan 101' or even when listing the menu.
Also, I am not able to get up the web interface......
But some of the commands, like 'show running' is working just fine.
The switch is in another building, connected through a wireless bridge. The clients are connected to the network, and are working properly.
The only problem for me is being able to manage the switch in a proper way, and I am afraid there is something really wrong....
I attach the config from the device.
Best regards
.:Rune:.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2008 04:38 PM
тАО12-05-2008 04:38 PM
Re: 2650 cli output hang
Hi Rune,
It could be relating to a problem that was reported concerning loss of management functionality of the switch,this has been fixed! I suggest you contact your local Procurve Support and ask for the latest firmware, released to support which is H.10.74
Good Luck!
It could be relating to a problem that was reported concerning loss of management functionality of the switch,this has been fixed! I suggest you contact your local Procurve Support and ask for the latest firmware, released to support which is H.10.74
Good Luck!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2008 03:52 PM
тАО12-06-2008 03:52 PM
Re: 2650 cli output hang
Yep, it is definitely worth to try it:
ftp://ftp.hp.com/pub/networking/software/2600-Software-H1074.zip
ftp://ftp.hp.com/pub/networking/software/2600-Software-H1074.zip
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-07-2008 11:39 PM
тАО12-07-2008 11:39 PM
Re: 2650 cli output hang
Thanks, I will try upgrading this morning and see if there are any changes.
.:Rune:.
.:Rune:.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP