- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- 2848 VLan problem PLEASE HELP!!
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-29-2011 07:13 AM
09-29-2011 07:13 AM
2848 VLan problem PLEASE HELP!!
I have the following code:
I need Vlan 1 to view / connect to all other VLANS, I am using a computer connected to VLAN2 and a DHCP / SNTP in VLAN1 (192.168.5.10)
DHCP seems to be working on all the VLANs and when I connect MY PC into each VLAN I receive an IP address, I can ping all VLAN addresses. But when I connect my PC into VLAN2 my software will only see what is in VLAN2 and not the other VLANs.
Is there something else I need to do?
Please help
Running configuration: ; J4904A Configuration Editor; Created on release #I.08.98 hostname "ProCurve Switch 2848" snmp-server contact "" snmp-server location "" ip default-gateway 192.168.5.10 ip routing snmp-server community "public" Unrestricted vlan 1 name "VLAN1" untagged 1,19-43,46-48 ip address 192.168.5.1 255.255.255.0 ip helper-address 192.168.5.10 no untagged 2-18,44-45 ip igmp ip irdp exit vlan 2 name "VLAN2" untagged 2-9 ip address 192.168.6.1 255.255.255.0 ip helper-address 192.168.5.10 ip igmp ip irdp exit vlan 3 name "VLAN3" untagged 10,44-45 ip address 192.168.7.1 255.255.255.0 ip helper-address 192.168.5.10 ip igmp ip irdp exit vlan 4 name "VLAN4" untagged 11-14,18 ip address 192.168.8.1 255.255.255.0 ip helper-address 192.168.5.10 ip igmp ip irdp exit vlan 5 name "VLAN5" untagged 15-17 ip address 192.168.9.1 255.255.255.0 ip helper-address 192.168.5.10 ip igmp ip irdp exit ip route 0.0.0.0 0.0.0.0 192.168.5.10
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-01-2011 05:44 PM
10-01-2011 05:44 PM
Re: 2848 VLan problem PLEASE HELP!!
code on switch is very old, current on HP site shows I.10.77
If you get the correct dhcp supplied IP address and mask for each VLAN, do you also get the correct gateway, path out to the other VLANs? If you only can talk to devices on the VLAN but not outside, I would suspect routing between the VLANs, not a switch config problem. Check your gateway set on your client when on each VLAN, is it set correctly and can you ping it.
good luck
jim