- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- 2910al switch config
Switches, Hubs, and Modems
1748266
Members
3537
Online
108760
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-16-2010 07:24 AM
08-16-2010 07:24 AM
2910al switch config
we have a 2910al switch that needs to connect to a cisco router. We have been given instructions to configure a port on our switch to talk to the router, but these are instructions for another cisco switch not a HP one. The instructions are as follows...
config t
port 23
description***Connection to Orange router-Fa0/1***
no switchport
ip address 10.xx.xxx.xxx 255.xxx.xxx.xxx
no ip redirects
no ip proxy-arp
speed 100
duplex full
no shut
ip route 10.xx.xx.x 255.xxx.xxx.xxx.x 10.xxx.xxx.xxx
end
Is this possible to do with a 2910al switch - I think it maybe but not sure if I have to do a vlan???
config t
port 23
description***Connection to Orange router-Fa0/1***
no switchport
ip address 10.xx.xxx.xxx 255.xxx.xxx.xxx
no ip redirects
no ip proxy-arp
speed 100
duplex full
no shut
ip route 10.xx.xx.x 255.xxx.xxx.xxx.x 10.xxx.xxx.xxx
end
Is this possible to do with a 2910al switch - I think it maybe but not sure if I have to do a vlan???
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-16-2010 08:10 AM
08-16-2010 08:10 AM
Re: 2910al switch config
Try this doc
www.tecnocael.it/ftp/docs/ProCurve_Cisco.pdf
The config on the 2910 side should be relatively simple.
Tore
www.tecnocael.it/ftp/docs/ProCurve_Cisco.pdf
The config on the 2910 side should be relatively simple.
Tore
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP