- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: 3Com 4800G and procuvre 2610 Vlan setup
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2012 09:08 AM
тАО02-14-2012 09:08 AM
3Com 4800G and procuvre 2610 Vlan setup
I replacing my procure 2910al with a Com 4800G.
I am just getting to grips with the command line of the 3 Com and I need to configure it to do the following.
I am up linking 5 procuvre 2610 with two vlans
data
voice
voice vlan is on 172.16.17.0/24
data vlan is on 192.168.2.0/24
PC are plugged into the Phones and pick up DHCP accordingly .
The voice vlan is tagged and the data vlan is untagged the trunk ports are tagged.
I have tried to do the same on the 3 com but when I tagged the trk port on the procurve vlan everything stops working.
has any one got any sample configuration for HP to 3com vlans
Also my DHCP server is going into the 3com and I cannot get the traffic from the 3com to the HP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2012 10:14 PM
тАО02-14-2012 10:14 PM
Re: 3Com 4800G and procuvre 2610 Vlan setup
Can you provide the relevant config from both sides of the 3Com and ProCurve?
CCIE Service Provider
MASE Network Infrastructure [2011]
H3CSE
CCNP R&S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2012 05:34 AM
тАО02-15-2012 05:34 AM
Re: 3Com 4800G and procuvre 2610 Vlan setup
Procurve switch
; J9089A Configuration Editor; Created on release #R.11.30 hostname "ProCurve Switch 2610-48-PWR" trunk 49-50 Trk1 LACP ip default-gateway 172.16.17.117 snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1,3-48,51-Trk1 ip address 172.16.17.119 255.255.255.0 ip helper-address 172.16.17.2 no untagged 2 exit vlan 2 name "VLAN2" ip address 192.168.17.119 255.255.255.0 ip helper-address 172.16.17.2 tagged 1-48,Trk1 exit vlan 3 name "Vlan3" exit vlan 4 name "Vlan 4" untagged 2 ip address 10.10.20.202 255.255.255.0 tagged 1,3-48,51-Trk1 voice exit fault-finder bad-driver sensitivity high fault-finder bad-transceiver sensitivity high fault-finder bad-cable sensitivity high fault-finder too-long-cable sensitivity high fault-finder over-bandwidth sensitivity high fault-finder broadcast-storm sensitivity high fault-finder loss-of-link sensitivity high fault-finder duplex-mismatch-HDx sensitivity high fault-finder duplex-mismatch-FDx sensitivity high gvrp no stack spanning-tree spanning-tree Trk1 priority 4
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2012 06:35 AM
тАО02-15-2012 06:35 AM
Re: 3Com 4800G and procuvre 2610 Vlan setup
The ports on the 3Coms that are part of link-aggregation should probably not be stp edged-port enable
CCIE Service Provider
MASE Network Infrastructure [2011]
H3CSE
CCNP R&S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2012 07:11 AM
тАО02-15-2012 07:11 AM
Re: 3Com 4800G and procuvre 2610 Vlan setup
I cannot seem to get the Mitel traffic to the Procurves.
I untagged the ports on vlan 4 which is the voice vlan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2012 07:16 AM
тАО02-15-2012 07:16 AM