- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- 5406zl update command
Switches, Hubs, and Modems
1753253
Members
4124
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2007 12:58 AM
тАО08-03-2007 12:58 AM
5406zl update command
After enter the update command in CLI, switch reboot and not boot again.
All LED's on Management Module is On.
Power, Fault and Locator LED's is On.
Serial Console not respond.
How solve this problem ?
Sory, I'am bad known English... :(
All LED's on Management Module is On.
Power, Fault and Locator LED's is On.
Serial Console not respond.
How solve this problem ?
Sory, I'am bad known English... :(
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2007 11:18 AM
тАО08-03-2007 11:18 AM
Re: 5406zl update command
I think the update command will reboot the switch into the bootROM. Just reset it again via the front panel or pull the power.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-04-2007 01:41 AM
тАО08-04-2007 01:41 AM
Re: 5406zl update command
ProCurve Switch 5412zl(config)# update
The device will be rebooted to Monitor ROM Console.
This will take the switch offline and allow only direct console access.
Do you want to continue [y/n]?
After this you will end up with:
Copyright (c) 1995-2005 Hewlett-Packard Company. All rights reserved.
RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure by the Government is subject to restrictions
as set forth in subdivision (b) (3) (ii) of the Rights in Technical Data and
Computer Software clause at 52.227-7013.
Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94303
Enter h or ? for help.
=>
Just type "boot" after the prompt.
You will end up with:
Boot Profiles:
0. Monitor ROM Console
1. Primary firmware image
2. Secondary firmware image
Select profile (monitor): 1
Booting Primary firmware image...
Decompressing...done.
initializing...
Waiting for Speed Sense. Press twice to continue.
The device will be rebooted to Monitor ROM Console.
This will take the switch offline and allow only direct console access.
Do you want to continue [y/n]?
After this you will end up with:
Copyright (c) 1995-2005 Hewlett-Packard Company. All rights reserved.
RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure by the Government is subject to restrictions
as set forth in subdivision (b) (3) (ii) of the Rights in Technical Data and
Computer Software clause at 52.227-7013.
Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94303
Enter h or ? for help.
=>
Just type "boot" after the prompt.
You will end up with:
Boot Profiles:
0. Monitor ROM Console
1. Primary firmware image
2. Secondary firmware image
Select profile (monitor): 1
Booting Primary firmware image...
Decompressing...done.
initializing...
Waiting for Speed Sense. Press
ProCurve Networking Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-04-2007 01:30 PM
тАО08-04-2007 01:30 PM
Re: 5406zl update command
I solve this problem.
Baud-rate on startup = 9600
When baud-rate = 11500 serial console not respond.
Baud-rate on startup = 9600
When baud-rate = 11500 serial console not respond.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP