- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Blade/GBE2 vlan config
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-05-2006 11:57 PM
тАО02-05-2006 11:57 PM
-Miika
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2006 02:12 AM
тАО02-07-2006 02:12 AM
SolutionOn the GbE2, the entire port is tagged rather than the individual VLAN. As a result, when you tag the port, all VLANs will be tagged.
We will be releasing a version of the firmware in the next couple of months that will allow untagging the default/native/PVID VLAN only if needed.
Yes, the crossconnect ports (17/18) should have all the appropriate VLANs added to them. A general guideline is to configure the crossconnect ports (17/18) the same as the uplink ports (19-22).
Best regards,
-sean
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2006 05:56 AM
тАО02-07-2006 05:56 AM
Re: Blade/GBE2 vlan config
-Miika
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2006 06:02 AM
тАО02-07-2006 06:02 AM
Re: Blade/GBE2 vlan config
For instance, you can use port trunking on the GbE2 to a Cisco or a Nortel or an Intel or a ProCurve, etc. as long as you manually configure the port trunk on both ends.
I have not heard that FEC will be dumped on ProCurves. Even if the term "FEC" is dumped, port trunking between a ProCurve and a Cisco will still work. Whether or not the ProCurve and the Cisco can use PAgP to automatically establish the trunk is a different issue. I have no idea what ProCurve's plans are concerning support of PAgP.
Hope this helps,
-sean
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2006 06:21 AM
тАО02-07-2006 06:21 AM
Re: Blade/GBE2 vlan config
Regarding your question of supporting FEC.
Yes, FEC will be discontinued with new firmware releases. Read the statement here:
ftp://ftp.hp.com/pub/networking/software/LLDP-and-LACP-statement.pdf
Sean is correct that, if statically configured, trunks (HP naming) will still work.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-21-2007 01:31 AM
тАО05-21-2007 01:31 AM
Re: Blade/GBE2 vlan config
I want to interconnect a GbE2 switch with a Procurve 5308xl switch via trunk link. FEC wont be supported on the ProCurve switch any more. I dont have any testing possibilities, could you tell me if following configuration will work?
Procurve 5308xl:
Static trunking, Trunk type to Trunk on the ProCurve
===========================- TELNET - MANAGER MODE -============================
Switch Configuration - Port/Trunk Settings
Port Type Enabled Mode Flow Ctrl Group Type
---- --------- + ------- ------------ --------- ----- -----
A23 1000T | Yes Auto Disable Trk1 Trunk
A24 1000T | Yes Auto Disable Trk1 Trunk
==================================
==================================
GbE2 Switch:
/c/port 21/gig
fctl both
speed any
mode full
auto on
/c/port 22/gig
fctl both
speed any
mode full
auto on
/c/trunk 3
ena
add 21
add 22