Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Catalyst 3020 blade witch for hp. Problems withs p...
Switches, Hubs, and Modems
turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
-
Categories
- Topics
- Hybrid IT with Cloud
- Mobile & IoT
- IT for Data & Analytics
- Transformation
- Strategy and Technology
- Products
- Cloud
- Integrated Systems
- Networking
- Servers and Operating Systems
- Services
- Storage
- Company
- Events
- Partner Solutions and Certifications
- Welcome
- Welcome
- Announcements
- Tips and Tricks
- Feedback
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- Converged Data Center Infrastructure
- Digital Transformation
- Grounded in the Cloud
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- Networking
- OEM Solutions
- Servers: The Right Compute
- Telecom IQ
- Transforming IT
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Categories
-
Forums
-
Blogs
-
InformationEnglish
Catalyst 3020 blade witch for hp. Problems withs ports going err-disable
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-04-2009 03:52 AM
12-04-2009 03:52 AM
Catalyst 3020 blade witch for hp. Problems withs ports going err-disable
Catalyst 3020 blade witch for hp. Problems withs ports going err-disable
Hello all!
I know this maybe be the right forum for this questin, nut I´m hoping that someone can give men an answer. Since I´m a newbe to Cisco and switches I use the Cisco Network Assistans go help me access the SAN switches.
As i mentioned in the subject the ports gets in err-disable mode on the switch almost all of the time I restarts the host. I have to disable and then enable to port to get it up again. I also get this message in the switch:
This port has been disabled becasue Link has been found to be fluctuating between up and down states rapidly.
Reason could be bad physical connector hardware or drivers on the switch port och connecting device is faulty.
Recommendation: Replace physical connector or upgrade drivers on switch port or try replacing cable and enable port again.
Is some setting I can change on the switch to make this dissapear? Any commands in telnet againt the switch?
I know this maybe be the right forum for this questin, nut I´m hoping that someone can give men an answer. Since I´m a newbe to Cisco and switches I use the Cisco Network Assistans go help me access the SAN switches.
As i mentioned in the subject the ports gets in err-disable mode on the switch almost all of the time I restarts the host. I have to disable and then enable to port to get it up again. I also get this message in the switch:
This port has been disabled becasue Link has been found to be fluctuating between up and down states rapidly.
Reason could be bad physical connector hardware or drivers on the switch port och connecting device is faulty.
Recommendation: Replace physical connector or upgrade drivers on switch port or try replacing cable and enable port again.
Is some setting I can change on the switch to make this dissapear? Any commands in telnet againt the switch?
1 REPLY
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-04-2009 08:01 AM
12-04-2009 08:01 AM
Re: Catalyst 3020 blade witch for hp. Problems withs ports going err-disable
Re: Catalyst 3020 blade witch for hp. Problems withs ports going err-disable
You can make it go away or (what is probably more appropriate) you can enable the auto-recovery of the port so that if it is disabled due to the link flapping it will be automatically re-enabled after 5 minutes.
The command for that is "errdisable recovery cause link-flap"
You can also change the default time of 5 minutes (300 s) to something a bit lower with "errdisable recovery interval X" (where X is a number in seconds)
The command for that is "errdisable recovery cause link-flap"
You can also change the default time of 5 minutes (300 s) to something a bit lower with "errdisable recovery interval X" (where X is a number in seconds)
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2018 Hewlett Packard Enterprise Development LP