- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Compatibility problem between 5300 modules?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2004 08:05 PM
тАО04-25-2004 08:05 PM
Compatibility problem between 5300 modules?
The switch can't came up, it reboots continually.
The only way to start the switch is to unplug the gbic and one of the Fastethernet module (this one seems to be a different version from the other three).
If i plug in the gbic and the fast ethernet module and unplug the other trhee, the switch starts too.
I updated the firmware to the 8.03 release, but this didn't help.
Any suggestion?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2004 05:52 AM
тАО04-26-2004 05:52 AM
Re: Compatibility problem between 5300 modules?
Does the reboots result in a crash message in the event log or 'show boot' CLI command?
Regards,
Ralph
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2004 06:39 PM
тАО04-26-2004 06:39 PM
Re: Compatibility problem between 5300 modules?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2004 09:57 PM
тАО04-26-2004 09:57 PM
Re: Compatibility problem between 5300 modules?
then disconnect the gb-module,
then (i hope you have the cli ) and you can copy the crash-log.
but i take it that the gb-module is the CRASH.
helps?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2004 03:15 AM
тАО04-28-2004 03:15 AM
Re: Compatibility problem between 5300 modules?
If you connect a VT terminal to the console port of the switch, you'll be able to see the crash and continuous reboot. Set the your terminal to operate at 9600 N81.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2004 09:31 PM
тАО04-29-2004 09:31 PM
Re: Compatibility problem between 5300 modules?
You can also try to look inside crash-logs. Look for valuable info.
#copy ?
event-log Copy event log file.
crash-data Copy the switch crash data file.
crash-log Copy the switch log file.
Check boot prom version also.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2004 08:56 AM
тАО05-01-2004 08:56 AM
Re: Compatibility problem between 5300 modules?
Does it say something like:
Bus error: HW Addr=0x06836252 IP=0x00444f14 Task='mHttpCtrl' Task ID=0x11257f8 ??
If not please specify.
Thanks, Ardon