- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Create a basic VLAN on Procurve 2848
Switches, Hubs, and Modems
1753481
Members
4053
Online
108794
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-23-2011 03:34 AM
тАО03-23-2011 03:34 AM
Hi! I'm trying to make 2 VLANS in my switch, before i was a cisco switch and i had 2 vlans "by ports" that works really well but now im trying to make the same thing on HP Swith but i can't.
I dont wanna make trunk, routing, or something else, just "isolate" a few port from default VLAN and use it like a separated switch.
My current config (that it's not working) is:
Running configuration:
; J4904A Configuration Editor; Created on release #I.10.77
hostname "ProCurve Switch 2848"
ip default-gateway 192.168.0.1
snmp-server community "secret" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged 1-32,45-48
ip address 192.168.0.180 255.255.255.0
no untagged 33-44
exit
vlan 10
name "VLAN_10"
untagged 33-38
no ip address
voice
exit
"vlan 20
name "VLAN_20"
untagged 39-44
no ip address
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
no stack
password manager
password operator
---------------------------------------------
Please help!
thanks
I dont wanna make trunk, routing, or something else, just "isolate" a few port from default VLAN and use it like a separated switch.
My current config (that it's not working) is:
Running configuration:
; J4904A Configuration Editor; Created on release #I.10.77
hostname "ProCurve Switch 2848"
ip default-gateway 192.168.0.1
snmp-server community "secret" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged 1-32,45-48
ip address 192.168.0.180 255.255.255.0
no untagged 33-44
exit
vlan 10
name "VLAN_10"
untagged 33-38
no ip address
voice
exit
"vlan 20
name "VLAN_20"
untagged 39-44
no ip address
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
no stack
password manager
password operator
---------------------------------------------
Please help!
thanks
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-23-2011 05:08 AM
тАО03-23-2011 05:08 AM
Solution
Hi! If you only want to have local isolated vlan (10, 20) so there is no other communication needed for them or between them except between untagged ports in this vlan then your config should work. Just assign ip addresses to clients in this vlan (connect DHCP to vlan or set manually). No default gateway needed because communication is isolated only between vlan ports.
If you need communication between vlans or anywhere from this switch you have to span vlans to router (tag uplink ports) or configure ip routing and then possibly make some filtering through ACLs.
If you need communication between vlans or anywhere from this switch you have to span vlans to router (tag uplink ports) or configure ip routing and then possibly make some filtering through ACLs.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2011 07:56 AM
тАО03-25-2011 07:56 AM
Re: Create a basic VLAN on Procurve 2848
vlan 10
untagged 33-38
exit
Is all that's needed to isolate some ports in a separate (v) lan.
why it's not working?
maybe no need to issue an "apply" command, before the changes are activated?
untagged 33-38
exit
Is all that's needed to isolate some ports in a separate (v) lan.
why it's not working?
maybe no need to issue an "apply" command, before the changes are activated?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP