- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Dns client on Procurve switches?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2008 12:54 AM
08-14-2008 12:54 AM
Does Procurve switches has a dns-client? (If you wanted to use hostnames for sntp servers, tftp servers or similar.)
If so, how do you configure it?
(I know that IP addresses reduces risks of errors in most cases, but I am curious if it is possible to use dns.)
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2008 01:04 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2008 04:41 AM
08-14-2008 04:41 AM
Re: Dns client on Procurve switches?
Thank you for the reply. I checked it out on our 5406 and it accepted the command. A few other switch models did not support it.
However, on the 5606 I did not find any command or tool (copy tftp, sntp server, telnet, ping, traceroute..) that could actually accept a hostname instead of Ip addresses.
Should the conclusion be that Procurve switches must use only IP in the configuration and tools?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2008 04:57 AM
08-14-2008 04:57 AM
Re: Dns client on Procurve switches?
with K.13.xx for the 5400 the cli-command changed a little
ip dns server-address priority 1
hope this helps
ben
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2008 05:11 AM
08-14-2008 05:11 AM
Re: Dns client on Procurve switches?
>with K.13.xx for the 5400 the cli-command
>changed a little
>ip dns server-address priority 1
I saw that too, and the same was true for sntp server-command, which also had added priority (very good!)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-21-2017 05:05 AM
03-21-2017 05:05 AM
Re: Dns client on Procurve switches?
Procurve 2910al
----------------------------------------------------------
#conf t
#ip dns server-address priority 1 208.67.222.222
#save
#show ip
----------------------------------------------------------