- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- FCS Errors on HP 2626 (J4900B)
Switches, Hubs, and Modems
1748184
Members
3900
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-16-2006 10:06 PM
11-16-2006 10:06 PM
FCS Errors on HP 2626 (J4900B)
Hi all,
At one of our customers we had to connect a new HP Procurve 2626 to an existing Avaya P332G-ML. Both were equiped with new 1000Base-SX SFP gbics.
The HP's uplink port immediately started showing FCS errors and has continued to do so ever since. The corresponding port on the Avaya shows no errors. There is no duplex mismatch, the connecting FO cable has been tested, the patchcords have been exchanged...
Any more ideas?
Thanks!
At one of our customers we had to connect a new HP Procurve 2626 to an existing Avaya P332G-ML. Both were equiped with new 1000Base-SX SFP gbics.
The HP's uplink port immediately started showing FCS errors and has continued to do so ever since. The corresponding port on the Avaya shows no errors. There is no duplex mismatch, the connecting FO cable has been tested, the patchcords have been exchanged...
Any more ideas?
Thanks!
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-17-2006 07:44 PM
11-17-2006 07:44 PM
Re: FCS Errors on HP 2626 (J4900B)
Since it would be FCS Received errors, it implies that the traffic being sent from the Avaya is being corrupted at some point.
Try swapping the SFP's, try the SFP's in different ports, try swapping the fibre leads around so that what was TX becomes RX. Check that you don't have any single-mode cabling.
Try swapping the SFP's, try the SFP's in different ports, try swapping the fibre leads around so that what was TX becomes RX. Check that you don't have any single-mode cabling.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP