- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- HP 4104 VLAN question
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-18-2008 11:01 AM
тАО03-18-2008 11:01 AM
I'm trying to configure a VLAN on this switch and not having much luck. I've successfully created the VLAN and added 1 (C20) port. The switch IP is 10.1.1.250/24. The VLAN IP is 10.1.3.254/24. I cannot ping the VLAN IP, but I can ping the switch. If I plug a device into C20 I can ping the VLAN, but not the switch. I've enable IP routing as well. If I issue "show ip route" I do not see the 10.1.3.x network listed. It will not take a static route either. Any ideas how I can get the switch to recognize that it is supporting 2 networks?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-18-2008 12:35 PM
тАО03-18-2008 12:35 PM
Re: HP 4104 VLAN question
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-19-2008 07:59 AM
тАО03-19-2008 07:59 AM
Re: HP 4104 VLAN question
Here's a copy of my config...
HP ProCurve Switch 4104GL# sh conf
Startup configuration:
; J4887A Configuration Editor; Created on release #G.07.104
hostname "HP ProCurve Switch 4104GL"
snmp-server contact "DPower"
snmp-server location "3rd Floor Closet"
no cdp run
module 4 type J4864A
module 1 type J4908A
module 2 type J4908A
module 3 type J4908A
interface D3
disable
exit
interface A1
no lacp
exit
interface A2
no lacp
exit
interface A3
exit
interface C20
no lacp
exit
interface C21
no lacp
exit
interface C22
no lacp
exit
ip default-gateway 10.1.1.254
ip routing
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged A1-A22,B1-B22,C1-C19,C21-C22,D1-D3
ip address 10.1.1.248 255.255.255.0
ip helper-address 10.1.1.231
no untagged C20
exit
vlan 300
name "VLAN300"
untagged C20
ip address 10.1.3.254 255.255.255.0
ip helper-address 10.1.1.231
exit
ip route 0.0.0.0 0.0.0.0 10.1.1.254
management-vlan 1
spanning-tree
HP ProCurve Switch 4104GL#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-19-2008 01:04 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-19-2008 02:37 PM
тАО03-19-2008 02:37 PM