HP Procurve 2610-24 stuck on test LED, no networking

[nmcain]

Hello

I have a Procurve 2610 that was working well, until when I tried to turn it on today, it would not pass the boot test sequence. It does the thing where it flashes all the LEDs on the front, the POE test, and then it just stops, with the green test light stuck on. Are there jumpers on the board I can use to disable the test or what would I do to fix this?

[nmcain]

I hooked it up over serial, it now says the following: 

ROM information:
   Build directory: /sw/rom/build/nemorom(ndx)
   Build date:      Nov 28 2007
   Build time:      16:36:54
   Build version:   R.10.06
   Build number:    14201

OS identifier found at @ 0xbc020000
Verifying Image validity ...
CRC on OS image header Passed
CRC on complete OS image file Passed
Valid OS image @ 0xbc020000

Decompressing...done.
CRC of image is 0x9f03940e
CRC @ 0x80001000 Len 10102672 is 0x9f03940e



initializing..

[akg7]

Hello,

Form below output it seems switch is initialiazing.

Afterwards any other message comes or its stucked here?

Thanks!

[nmcain]

I let it sit for 12 hours, unfortunately, it is frozen initializing.  There is no additional output other than just that little initializing text and the standard bootup information.

[nmcain]

I was able to get it to show debug information, is this helpful?

[akg7]

Hello,

Please share the show debug information if it was collected. 

Also have you treid to factory reset the device?

What is the current software version in the device?

Thanks!

[nmcain]

I showed the debug information in the attached picture above, I have factory reset it several times, It is running R.10.06, from November 28, 2007 build number 14201, which is old but was completely working fine until the issue began.

[akg7]

Hello,

Unfortunately I am unable to see debug snapshot.

Seeing only below:

How long switch was 'UP'?

Thanks!

[nmcain]

Here's the debug info in text: 

Task 'swInitTask' ID = 0x85f72860 suspended prior to switch_init
Bring up GDB and attach to the swInitTask task or taskResume the swInitTask via WindShell

The switch was on and offline sporadically, with the power outage it had been off for about 2 days, with a total uptime of probably around ~1500 hours

[nmcain]

I have attempted to upgrade the firmware, it still doesnt function, which leads me to believe this is indeed some sort of hardware failure, since it can't pass its bootup testing sequence.

heres the log from the installation

ROM information:
   Build directory: /sw/rom/build/nemorom(ndx)
   Build date:      Nov 28 2007
   Build time:      16:36:54
   Build version:   R.10.06
   Build number:    14201

OS identifier found at @ 0xbc020000
Verifying Image validity ...
CRC on OS image header Passed
CRC on complete OS image file Passed
Valid OS image @ 0xbc020000
Press any key for ROM prompt

HP ProCurve Switch 2610-24-PWR (J9087A)
ROM Build Directory: /sw/rom/build/nemorom(ndx)
        ROM Version: R.10.06
     ROM Build Date: 16:36:54 Nov 28 2007
   ROM Build Number: 14201

Copyright (c) 1995-2001 Hewlett-Packard Company. All rights reserved.

                         RESTRICTED RIGHTS LEGEND

Use, duplication, or disclosure by the Government is subject to restrictions
as set forth in subdivision (b) (3) (ii) of the Rights in Technical Data and
Computer Software clause at 52.227-7013.

    Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94303

Enter h or ? for help.

=>h

LAN Monitor Commands

  do(wnload)                      - Download via Xmodem
  sp(eed) <baud>                  - Set a new baud rate
  h(elp)                          - Display help screen
  ?                               - Display help screen
  id(entify)                      - Print out identification string
  jp(jump) <1|2>   - Jump to product code, optional 1-primary, 2-secondary
  q(uit)                          - Exit the monitor
  boot                            - Reboot the system
  reset                           - Reset the system
  v(ersion)                       - Display version information
=>sp 115200
=>h

LAN Monitor Commands

  do(wnload)                      - Download via Xmodem
  sp(eed) <baud>                  - Set a new baud rate
  h(elp)                          - Display help screen
  ?                               - Display help screen
  id(entify)                      - Print out identification string
  jp(jump) <1|2>   - Jump to product code, optional 1-primary, 2-secondary
  q(uit)                          - Exit the monitor
  boot                            - Reboot the system
  reset                           - Reset the system
  v(ersion)                       - Display version information
=>
=>
=>do

You have invoked the console download utility.
Do you wish to continue? (Y/N)>Download was successful.

 -- Download for this Product, proceeding --
pass CRC check (len=4050235)
, Erasing 62 segments..., Programming starting at 0xbc020000...
programming successful...
Ready for code execution.

Decompressing...done.
CRC of image is 0x27a5cee3
CRC @ 0x80001000 Len 11159792 is 0x27a5cee3

It sticks up here.