- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: HP Procurve J9087A crashes when attaching an A...
Switches, Hubs, and Modems
1753575
Members
6317
Online
108796
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2009 11:52 PM
тАО07-07-2009 11:52 PM
HP Procurve J9087A crashes when attaching an APC AP7921 to the network
Today i recieved two APC AP7921 PDU`s for colocation. When i connect one of these PDU`s to the network of my Procurve (J9087A) 2610-24-PWR the switch crashes and reboots.
The APC PDU`s are connect to port 3 using a basis 8 ports switch. This switch is always used to configure and install new devices. And is working fine with everything else.
The switch is configures with 3 vlan`s and DHCP snooping is active
dhcp-snooping
no dhcp-snooping option 82
dhcp-snooping vlan 12 14-15
power pre-std-detect
Switch Firmware:
Image stamp: /sw/code/build/nemo(ndx)
Oct 22 2008 16:11:27
R.11.22
193
Boot Image: Primary
The APC PDU`s are connect to port 3 using a basis 8 ports switch. This switch is always used to configure and install new devices. And is working fine with everything else.
The switch is configures with 3 vlan`s and DHCP snooping is active
dhcp-snooping
no dhcp-snooping option 82
dhcp-snooping vlan 12 14-15
power pre-std-detect
Switch Firmware:
Image stamp: /sw/code/build/nemo(ndx)
Oct 22 2008 16:11:27
R.11.22
193
Boot Image: Primary
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 08:29 AM
тАО07-09-2009 08:29 AM
Re: HP Procurve J9087A crashes when attaching an APC AP7921 to the network
Advise you to upgrade to version R.11.30
and try again.
and try again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 10:33 AM
тАО07-09-2009 10:33 AM
Re: HP Procurve J9087A crashes when attaching an APC AP7921 to the network
I already upgrade tot version 11.30. And the switch now doesn`t reboot when connection the APC Masterswitch to the network.
Im testing this week if the new version introduces new problems on the network.
Im testing this week if the new version introduces new problems on the network.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP