- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: HP2824 new subnet configured but cannot connec...
Switches, Hubs, and Modems
1753701
Members
4993
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-05-2006 02:06 AM
тАО08-05-2006 02:06 AM
Re: HP2824 new subnet configured but cannot connect
Hi
Based on the Map you attached before, the devault_vlan on your switch is 192.168.20.241 , but in the routing table its :
192.168.47.0/24 DEFAULT_VLAN 1 connected 0 0
Any explaination ???
Based on the Map you attached before, the devault_vlan on your switch is 192.168.20.241 , but in the routing table its :
192.168.47.0/24 DEFAULT_VLAN 1 connected 0 0
Any explaination ???
Science for Everyone
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-06-2006 08:04 PM
тАО08-06-2006 08:04 PM
Re: HP2824 new subnet configured but cannot connect
Hi, yes it was an error. Subnet 20 should read 47.
Thanks
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-05-2006 09:41 PM
тАО10-05-2006 09:41 PM
Re: HP2824 new subnet configured but cannot connect
Hello
Gave up with the VLAN method
The DEFAULT VLAN 1 is the 192.168.47.0/24 network, so I just set up a route for the new network, which is 192.168.120.0/24 to another port on the firewall (120.2) and added a mgt 192.168.120.241 to VLAN 1.
This kinda works, but it cannot browse everything. Internet and Voice works ok.
Is there anything else I need to do?
The HP2824 and all other 2600's have been upgraded to the latest Firmware.
Thanks
Gave up with the VLAN method
The DEFAULT VLAN 1 is the 192.168.47.0/24 network, so I just set up a route for the new network, which is 192.168.120.0/24 to another port on the firewall (120.2) and added a mgt 192.168.120.241 to VLAN 1.
This kinda works, but it cannot browse everything. Internet and Voice works ok.
Is there anything else I need to do?
The HP2824 and all other 2600's have been upgraded to the latest Firmware.
Thanks
- « Previous
-
- 1
- 2
- Next »
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP