- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- How do you turn off LACP on Procurve 5304xl ???
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-14-2003 11:55 AM
тАО08-14-2003 11:55 AM
it's causing problems on Macintosh machines and Appletalk broadcasts.
I have no idea what the command lines are to do this can any wonderfull person help out.
Desperate to sort this one asap.
P.S In dunces language if you please .
Thanks in advance.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-14-2003 06:39 PM
тАО08-14-2003 06:39 PM
Re: How do you turn off LACP on Procurve 5304xl ???
To remove a range of ports C1-C4 from a trunk you go into config mode then say:
no int e C1-C4 lacp
then
int e C1-C4 lacp passive
you can use the non-config mode command
show lacp
to see if it worked. You probably don't need to remove ports from a trunk first unless they have gotten confused but I put it in there because the example in the book shows it. You may want to look at chapter 9 in the HP ProCurve Series 5300XL Switches Management and Configuration Guide (Edition 7, April 2003)
at
http://www.hp.com/rnd/support/manuals/5300xl.htm
Ron
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 01:00 AM
тАО08-15-2003 01:00 AM
Re: How do you turn off LACP on Procurve 5304xl ???
In show LACP the status of LACP is active I am sure there must be a way to make it disabled as even in passive mode the ports are being blocked.
Attached two screen shots shows passive on all ports and log of blocked by LACP.
Gary
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 01:07 AM
тАО08-15-2003 01:07 AM
Re: How do you turn off LACP on Procurve 5304xl ???
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 06:26 AM
тАО08-15-2003 06:26 AM
SolutionYou need to telnet into the switch, and issue the following commands at the prompts:
HP ProCurve Switch 5304xl# conf t
HP ProCurve Switch 5304xl(config)# int all
HP ProCurve Switch 5304xl(eth-x-x)# no lacp
HP ProCurve Switch 5304xl(eth-x-x)# wr mem
just type in the bits that follow the "#" sign, and make sure the prompts before it look the same (or similar).
Where it says (eth-x-x), the x's will be the beginning and end ports selected (which is dependant on how many ports you have installed).
BTW - this will disable LACP on ALL PORTS IN THE SWITCH.
Regards,
Shane.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 06:31 AM
тАО08-15-2003 06:31 AM
Re: How do you turn off LACP on Procurve 5304xl ???
This is actually an Apple issue, based on the way the Appletalk protocol works (which BTW has similar issues with Spanning Tree Protocol).
See here for more info:
http://docs.info.apple.com/article.html?artnum=30922
Regards,
Shane.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 06:32 AM
тАО08-15-2003 06:32 AM
Re: How do you turn off LACP on Procurve 5304xl ???
I 08/15/03 11:26:15 ports: port B12 is now off-line
I 08/15/03 11:26:20 ports: port B12 is Blocked by LACP
I 08/15/03 11:26:23 ports: port B12 is now on-line
LACP momentarily blocks the port, but the on-line condition returns after a few seconds.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 06:38 AM
тАО08-15-2003 06:38 AM
Re: How do you turn off LACP on Procurve 5304xl ???
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-15-2003 06:42 AM
тАО08-15-2003 06:42 AM
Re: How do you turn off LACP on Procurve 5304xl ???
Kind Regards
Gary
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-21-2005 08:38 PM
тАО09-21-2005 08:38 PM