- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Inherited ProCurve 93xx
Switches, Hubs, and Modems
1753326
Members
4700
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-08-2003 07:37 AM
09-08-2003 07:37 AM
Inherited ProCurve 93xx
Hi all,
I have no experience with HP's CLI, however I am lucky enough to have inherited a 93xx Layer 3 switch. My problem is I will need to clear down its current config and return it to some kind of factory default, removing any IP, VLAN etc details in the running config. Its been inherited in its previous working state with all its config still set.I assume its similar to cisco IOS where startup config can be re-loaded into running config?
Im convinced the startup config is a copy of the running config, so it will not help copying startup into running. How can I reset this swithc back to a clean slate?
I would really appreicate any help,
Thanks
Simon
I have no experience with HP's CLI, however I am lucky enough to have inherited a 93xx Layer 3 switch. My problem is I will need to clear down its current config and return it to some kind of factory default, removing any IP, VLAN etc details in the running config. Its been inherited in its previous working state with all its config still set.I assume its similar to cisco IOS where startup config can be re-loaded into running config?
Im convinced the startup config is a copy of the running config, so it will not help copying startup into running. How can I reset this swithc back to a clean slate?
I would really appreicate any help,
Thanks
Simon
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-08-2003 10:21 AM
09-08-2003 10:21 AM
Re: Inherited ProCurve 93xx
http://www.hp.com/rnd/support/manuals/93xx_6308.htm
Has all the manuals on the beast.
From the command line in priv mode you can say:
erase startup-config
then reboot with:
reload
Ron
Has all the manuals on the beast.
From the command line in priv mode you can say:
erase startup-config
then reboot with:
reload
Ron
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP