- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- J4857A enable password reset
Switches, Hubs, and Modems
1753894
Members
7483
Online
108809
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-30-2006 02:20 AM
01-30-2006 02:20 AM
J4857A enable password reset
Hi,
Does anyone know to reset the enable password on a J4857A switch?
Thanks
Ben
Does anyone know to reset the enable password on a J4857A switch?
Thanks
Ben
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-30-2006 09:41 AM
01-30-2006 09:41 AM
Re: J4857A enable password reset
Taken from the security guide:
Recovering from a Lost Password
Recovery from a lost password requires direct access to the serial port and a system reset.
NOTE: You can perform this procedure only from the CLI.
To recover from a lost password:
1.
Start a CLI session over the serial interface to the device.
2.
Reboot the device.
3.
At the initial boot prompt at system startup, enter b to enter the boot monitor mode.
4.
Enter no password at the prompt. (You cannot abbreviate this command.) This command will cause the device to bypass the system password check.
5.
Enter boot system flash primary at the prompt.
6.
After the console prompt reappears, assign a new password.
Hope this helps,
Kell
Recovering from a Lost Password
Recovery from a lost password requires direct access to the serial port and a system reset.
NOTE: You can perform this procedure only from the CLI.
To recover from a lost password:
1.
Start a CLI session over the serial interface to the device.
2.
Reboot the device.
3.
At the initial boot prompt at system startup, enter b to enter the boot monitor mode.
4.
Enter no password at the prompt. (You cannot abbreviate this command.) This command will cause the device to bypass the system password check.
5.
Enter boot system flash primary at the prompt.
6.
After the console prompt reappears, assign a new password.
Hope this helps,
Kell
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP