- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: LACP
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 10:09 AM
тАО04-28-2008 10:09 AM
Thanks!
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 11:00 AM
тАО04-28-2008 11:00 AM
Solutionbefore two switch vlan 1 assign ip address
and you create telnet connection ...
sw2810# conf
sw2810(config)# trunk 21-22 trk1 lacp
sw2610# conf
sw2610(config)# trunk 25-26 trk1 lacp
you write each switch above command and two switch attach two utp patchcord.
gool luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 07:18 AM
тАО04-29-2008 07:18 AM
Re: LACP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 07:52 AM
тАО04-29-2008 07:52 AM
Re: LACP
Jun 6 2006 14:11:54
N.10.02
419
Boot Image: Primary
BTW when i tried those commands it started playing some real havoc with the current live switches they were connected to. This caused several servers to go down briefly until i unplugged the switches from our network. :-/ There connected to the network again but without the Trunk command.
Does this essentially do the same thing?
Int 20 LACP ACTIVE
INT 19 LACP ACTIVE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 09:21 AM
тАО04-29-2008 09:21 AM
Re: LACP
Deploying the trunks live would definitely cause weird network behaviour!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 12:18 PM
тАО04-29-2008 12:18 PM
Re: LACP
In regards to my question, I enabled LACP on each interface that was connected to my new switches. I now have Dyn-1,Dyn-2, and Dyn3 (there are 3 2610's in this case). Does this indicate that LACP is working?
Thanks again!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2008 11:22 PM
тАО04-29-2008 11:22 PM
Re: LACP
on procurve switch two trunk methot
LACP and Hp trunk
LACP default settings enable all port
you can connect one server with team nic
and see procurve switch this team nic.and create ports dynamic lacp trunk.
you want two switch between connect trunk connection ,you make above my trunk config.
for more info:
ftp://ftp.hp.com/pub/networking/software/59906028_ch07.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 06:38 AM
тАО05-01-2008 06:38 AM
Re: LACP
Also, I went to download the most recent firmware and HP's website is having problems. I go here http://www.hp.com/rnd/software/j90851107.htm and click download and I get a ISS error.. Anyone know of an alternative location?