- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Multifunction NIC on Proliant DL380
Switches, Hubs, and Modems
1753284
Members
5439
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2008 11:47 AM
03-17-2008 11:47 AM
Multifunction NIC on Proliant DL380
I have a proliant DL380 G5 that I am trying to install a NC510F multifunction Nic card in.
Have tried several times to install the driver without success. When checking the BIOS I noticed that the card isn't being recognized correctly.
The system sees the following:
PCI Slot 5 - Unknown PCI Device
PCI Slot 5 - SCSI Mass Storage Controller
The integrated Nics are seen correctly as nics/iscsi devices.
Is there a jumper setting that I need to change. The BIOS is at the latest version.
Thanks
Have tried several times to install the driver without success. When checking the BIOS I noticed that the card isn't being recognized correctly.
The system sees the following:
PCI Slot 5 - Unknown PCI Device
PCI Slot 5 - SCSI Mass Storage Controller
The integrated Nics are seen correctly as nics/iscsi devices.
Is there a jumper setting that I need to change. The BIOS is at the latest version.
Thanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-18-2008 09:28 AM
03-18-2008 09:28 AM
Re: Multifunction NIC on Proliant DL380
Probably not the correct subforum but still...
Under which OS are you trying to do this, and from whence did you get the driver you are trying to install?
I've installed NC510F's in DL380G5's under RedHat 5.0 and 5.1 without much difficulty, although I had to go to www.hp.com and follow the drivers link to get the driver - and the NIC firmware - required.
Under which OS are you trying to do this, and from whence did you get the driver you are trying to install?
I've installed NC510F's in DL380G5's under RedHat 5.0 and 5.1 without much difficulty, although I had to go to www.hp.com and follow the drivers link to get the driver - and the NIC firmware - required.
there is no rest for the wicked yet the virtuous have no pillows
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP