- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: POE PSE State is off on A5120-EI POE Switch
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-02-2012 08:53 AM
тАО11-02-2012 08:53 AM
POE PSE State is off on A5120-EI POE Switch
I have a A5120-EI POE Switch with 4 in a stack. 2 of 4 switches are delivering power
to VoIP phones however 2 are not.
[FWRI-RMI1-1]display poe device
PSE ID SlotNo SubSNo PortNum MaxPower(W) State Model
4 1 0 48 370 on PD67124
7 2 0 48 370 off PD67124
10 3 0 48 370 on PD67124
13 4 0 48 370 off PD67124
How do I change the PSE State to on?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2012 12:28 PM
тАО11-03-2012 12:28 PM
Re: POE PSE State is off on A5120-EI POE Switch
[Switch] interface x/x/x
[Switch-GigabitEthernetx/x/x] poe enable
PoE on Comware is disabled by default, and must enabled per port.
hth...Jeff
PS:
Another good source of info, the HP Networking and Cisco CLI Reference Guide. A free CLI ref of ProVision, Comware5, and Cisco in side-by-side comparison. Not all inclusive, but alot of the "daily" config needs. ....and it's free!
Also good if you have a single platform :-)
https://h30590.www3.hp.com/product/HP+Networking+and+Cisco+CLI+Reference+Guide-PDF-6997
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2017 10:54 PM - edited тАО12-05-2017 10:55 PM
тАО12-05-2017 10:54 PM - edited тАО12-05-2017 10:55 PM
Re: POE PSE State is off on A5120-EI POE Switch
I believe the state transfers to on as soon as both of following conditions are met:
1.- you enabled poe on the interfaces
2.- you have a poe device connected to an interface of that irf member.