- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: ProCurve 2824 trunking to Cisco 3560 switch. T...
Switches, Hubs, and Modems
1753511
Members
4905
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-21-2005 04:35 AM
тАО04-21-2005 04:35 AM
Hi All,
I can't get to any of the manuals at;
http://www.hp.com/rnd/support/manuals/2800.htm
So I can't verify the correct configuration for the HP ProCurve Switch.
End-result. I want to aggregate two cables to create a 2-gig pipe. The HP will only know it's one VLAN and anything received by the Cisco switch will be considered it's VLAN100. So a trunk on the HP side and a channel-group on Cisco. This is the Cisco config;
interface Port-channel1
switchport access vlan 100
switchport mode access
interface GigabitEthernet0/1
description Uplink to HP ProCurve 24-Port Switch
switchport access vlan 100
switchport mode access
channel-group 1 mode active **
!
interface GigabitEthernet0/2
description Uplink to HP ProCurve 24-Port Switch
switchport access vlan 100
switchport mode access
channel-group 1 mode active **
**From Cisco
Active - Enables LACP only if a LACP device is detected. It places the port into an active negotiating state in which the port starts negotiations with other ports by sending LACP packets.
What's the proper HP way to trunk two gig ports using LACP?
Thanks, Tim
I can't get to any of the manuals at;
http://www.hp.com/rnd/support/manuals/2800.htm
So I can't verify the correct configuration for the HP ProCurve Switch.
End-result. I want to aggregate two cables to create a 2-gig pipe. The HP will only know it's one VLAN and anything received by the Cisco switch will be considered it's VLAN100. So a trunk on the HP side and a channel-group on Cisco. This is the Cisco config;
interface Port-channel1
switchport access vlan 100
switchport mode access
interface GigabitEthernet0/1
description Uplink to HP ProCurve 24-Port Switch
switchport access vlan 100
switchport mode access
channel-group 1 mode active **
!
interface GigabitEthernet0/2
description Uplink to HP ProCurve 24-Port Switch
switchport access vlan 100
switchport mode access
channel-group 1 mode active **
**From Cisco
Active - Enables LACP only if a LACP device is detected. It places the port into an active negotiating state in which the port starts negotiations with other ports by sending LACP packets.
What's the proper HP way to trunk two gig ports using LACP?
Thanks, Tim
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-21-2005 06:14 PM
тАО04-21-2005 06:14 PM
Solution
Tim,
In fact you have tree methods.
-LACP
-Cisco FEC
-HP Trunking
HP config in case of FEC:
trunk 1-2 trk1 fec
or in case of LACP:
int eth 1-2
lacp active
trunk 1-2 trk1 lacp
in the HP cli you can also type help after every command, like:
trunk help
or
lacp help
Hopefully it helps
By the Way:
Cisco channel=HP Trunking
Cisco trunking= HP 802.1Q
In fact you have tree methods.
-LACP
-Cisco FEC
-HP Trunking
HP config in case of FEC:
trunk 1-2 trk1 fec
or in case of LACP:
int eth 1-2
lacp active
trunk 1-2 trk1 lacp
in the HP cli you can also type help after every command, like:
trunk help
or
lacp help
Hopefully it helps
By the Way:
Cisco channel=HP Trunking
Cisco trunking= HP 802.1Q
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2005 07:21 AM
тАО04-22-2005 07:21 AM
Re: ProCurve 2824 trunking to Cisco 3560 switch. Two Gig Ports.
Thanks Sietze I'll give that a try.
Tim
Tim
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP