- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: ProCurve 5308xl
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2006 03:53 AM
тАО08-07-2006 03:53 AM
The servers are already on different subnets - 192.168.0.x and 192.168.16.x - and communicate perfectly well, but a server replication app. needs to run on a separate subnet. The software producer suggests using 9.0.0.1 and 9.0.0.2 as ip's on either end.
Can anyone point me in the right direction?
Our current config, from 192.168.16.x end is attached.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2006 04:14 AM
тАО08-07-2006 04:14 AM
Re: ProCurve 5308xl
I have read the configuration and apparently you have multiple vlans with different IP addresses , and IP routing is enabled.
So its simple now, you just creat one more vlan with the IP address that replication application suggested, on both sides, then add ths vlan as tagged on the port that connects these 2 switches.
SW1(config)# Vlan 9 ip address 9.0.0.1/24
SW1(config)# Vlan 9 tag Hx - where Hx is port connects both routing switches.
SW2(config)# Vlan 9 ip address 9.0.0.2/24
SW2(config)# Vlan 9 tag Hx - where Hx is port connects both routing switches.
Now both servers can communicate with this new Vlan and with each other as well.
I hope this is what exactly you need as i understood from your question and the config.
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2006 04:14 AM
тАО08-09-2006 04:14 AM
Re: ProCurve 5308xl
One server is on 9.0.0.1, and the other is 9.0.0.2.
There is a WAN link between the two servers, vlan 3 on both switches, using 10.0.0.1/30 and 10.0.0.2/30.
I have attached the config from both switches, with the changes suggested (I hope).
Any other suggestions/instuctions would be gratefully received.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2006 11:33 AM
тАО08-09-2006 11:33 AM
Re: ProCurve 5308xl
Next you need to add an untagged port into each one of those VLANs, this is the port the servers will connect to.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2006 08:41 PM
тАО08-09-2006 08:41 PM
Re: ProCurve 5308xl
I am also getting ip conflicts when the servers are set to 9.0.0.1/9.0.0.2 which I didn't get before untagging the ports.
Have I missed something?
Should I have 'ip rip' under vlan 5?
Current config from both switches is attached.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2006 01:24 AM
тАО08-10-2006 01:24 AM
SolutionYou will also need to add ports H24 and D23 back as tagged ports again in addition to the new untagged ports which your servers are connected to.
There should be no need to add VLAN5 to your rip configuration as by default it will redistribute connected VLANs.
I've attached the configs as I think they should be.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2006 02:23 AM
тАО08-10-2006 02:23 AM
Re: ProCurve 5308xl
My reason for changing the subnet mask is security. Nothing else
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-10-2006 02:25 AM
тАО08-10-2006 02:25 AM