Switches, Hubs, and Modems
cancel
Showing results for 
Search instead for 
Did you mean: 

ProCurve Switch 2510G-24 and SNMP

ProCurve Switch 2510G-24 and SNMP

Hi,

where can I change the Port for my SNMP Traps?
I do not get any traps.

Hajo
43 REPLIES
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Hello Hajo,
have you configure an SNMP-Server?

Connect to the CLI:
configure
snmp-server

here you find any commands you need to configure.

Regards

Re: ProCurve Switch 2510G-24 and SNMP

Yes,

i´ll show you
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Can you reach the SNMP Server via ping?

Re: ProCurve Switch 2510G-24 and SNMP

yes,

it´s alive
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

And you have enable snmp and the communitys are the same on the server and on the switch?

Re: ProCurve Switch 2510G-24 and SNMP

I tested it with the attached settings and tehy are received.
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Try to enable the mib
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Sorry. Here is the command
configure
snmp-server mib hpSwitchAuthMIB included

Re: ProCurve Switch 2510G-24 and SNMP

Hi,

the result:

Invalid input: mib
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

snmp-server host all /serveraddress
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Maby you must install the switch mip on the SNMP Server

Re: ProCurve Switch 2510G-24 and SNMP

OK, but how can I do this?

And the error was on the switch, can it recognize so fast that the right mib is missing on the server?

Re: ProCurve Switch 2510G-24 and SNMP

snmp-server host all /serveraddress

does not function

Re: ProCurve Switch 2510G-24 and SNMP

Snmp Response Pdu Source-IP Information

Selection Policy : rfc1517


what does this mean?
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

RFC 1517 is CIDR (classless inter domain routing)

On one of my 2510G Switches the command

conf
snmp-server host all SERVERIP

works.

What kind of firmware have you installed?

Re: ProCurve Switch 2510G-24 and SNMP

Version: Y.11.08, ROM N.10.02

Re: ProCurve Switch 2510G-24 and SNMP

SWGE122(config)# snmp-server host all 10.25.10.34
Incomplete input: 10.25.10.34
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

Now put the subnetmask behind the ip and it works. you can also write the subnetmask in CIDR (255.255.255.0 = /24)

Re: ProCurve Switch 2510G-24 and SNMP

OK,

what does this command cause?
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

That all informations are send to the ServerIP
bolli
Frequent Advisor

Re: ProCurve Switch 2510G-24 and SNMP

yes

Re: ProCurve Switch 2510G-24 and SNMP

Hi, are you german????

Re: ProCurve Switch 2510G-24 and SNMP

Are you german?
yes????

the time stamp isn´t right....

Re: ProCurve Switch 2510G-24 and SNMP

muss man sich denn dann hier auf englisch unterhalten?