Problem with PoE handsets not receiving power from 2610

[Draven]

the switch is config for pre-standard POE. We have to order some cross-over cables.

I just cant understand why the on switch some dect units will work and other wont there all brand new, all to lastest standards but a small netgear POE switch will work when its 1/10th the cost of the procurve?

Thanks
Daniel

[cenk sasmaztin]

please test

shut down auto mdix mode on swithc port
with this command

(eth-18)# mdix-mode mdix

and connect strain true(non crossover)cable your ip phone

and make speed duplex fix switch port 100-full and ip phone 100 full

please say me result

[Draven]

Use port 10 as the test

Keys: W=Warning I=Information
M=Major D=Debug
---- Event Log listing: Events Since Boot ----
I 01/01/90 00:00:02 system: --------------------------------------------------
I 01/01/90 00:00:02 system: System went down: 01/01/90 03:39:31
I 01/01/90 00:00:02 system: Operator cold reboot from TELNET session.
I 01/01/90 00:00:22 udpf: DHCP relay agent feature enabled
I 01/01/90 00:00:22 stack: Stack Protocol enabled
I 01/01/90 00:00:23 tftp: Enable succeeded
I 01/01/90 00:00:23 system: System Booted.
I 01/01/90 00:00:23 cdp: CDP enabled
I 01/01/90 00:00:23 lldp: LLDP - enabled
I 01/01/90 00:00:23 ports: port 28 is now on-line
I 01/01/90 00:00:23 ip: network enabled on 192.168.21.12
I 01/01/90 00:00:33 ports: port 8 PD Detected.
I 01/01/90 00:00:33 ports: port 8 Applying Power to PD.
W 01/01/90 00:00:33 ports: port 10 PD Invalid Signature indication.
I 01/01/90 00:00:33 ports: port 14 PD Detected.
W 01/01/90 00:00:33 ports: port 14 PD Denied power due to insufficient power
allocation.
I 01/01/90 00:00:33 ports: port 18 PD Detected.
W 01/01/90 00:00:33 ports: port 18 PD Denied power due to insufficient power
allocation.
I 01/01/90 00:00:33 ports: port 20 PD Detected.
allocation.
I 01/01/90 00:00:34 ports: port 22 PD Detected.
W 01/01/90 00:00:34 ports: port 22 PD Denied power due to insufficient power
allocation.
I 01/01/90 00:00:34 ports: port 14 PD Detected.
I 01/01/90 00:00:34 ports: port 14 Applying Power to PD.
I 01/01/90 00:00:34 ports: port 18 PD Detected.
I 01/01/90 00:00:34 ports: port 18 Applying Power to PD.
I 01/01/90 00:00:34 ports: port 20 PD Detected.
I 01/01/90 00:00:34 ports: port 20 Applying Power to PD.
I 01/01/90 00:00:35 ports: port 22 PD Detected.
I 01/01/90 00:00:35 ports: port 22 Applying Power to PD.
I 01/01/90 00:00:40 ports: port 8 is now on-line
I 01/01/90 00:00:40 ports: port 14 is now on-line
I 01/01/90 00:00:41 ports: port 18 is now on-line
I 01/01/90 00:00:41 ports: port 20 is now on-line
I 01/01/90 00:00:42 ports: port 22 is now on-line
I 01/01/90 00:04:43 mgr: SME TELNET from 192.168.21.31 - MANAGER Mode

this from a fresh boot.

Thanks
Daniel

[cenk sasmaztin]

can you make
fix port 100 base full
and mdix config

[Javed Padinhakara]

which firmware version do you have on this problematic MITEL phone? Are these the same as the ones in other phones which are working?

Many times we were able to solve lot of such problems by keeping the firmware to the latest 7.x version.

Make sure to read this before trying any firmware upgrade stuff on the MITEL boxes:

http://www.voip-info.org/wiki/view/Mitel+SIP+Firmware


HTH
Javed