- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Problems with ProCurve1800 after FW upgrade
Switches, Hubs, and Modems
1752511
Members
5042
Online
108788
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 12:51 AM
тАО10-12-2009 12:51 AM
Hello
I upgraded a ProCurve Switch 1800-24G (J9028B) to firmware PB.03.02
After the upgrade I cannot choose witch VLAN should be untagged.
The PVID field only contains VLAN1.
I tried resetting to factory defaults, and adding VLANs again, but still the same.
So I decided to downgrade to get the system up again, but now I cannot downgrade to older FW than PB.03.01, and this release I cannot find.
Need some quick tips here to get the system running...
I upgraded a ProCurve Switch 1800-24G (J9028B) to firmware PB.03.02
After the upgrade I cannot choose witch VLAN should be untagged.
The PVID field only contains VLAN1.
I tried resetting to factory defaults, and adding VLANs again, but still the same.
So I decided to downgrade to get the system up again, but now I cannot downgrade to older FW than PB.03.01, and this release I cannot find.
Need some quick tips here to get the system running...
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 01:10 AM
тАО10-12-2009 01:10 AM
Solution
Hi,
Have you tried the full-blown factory reset? (page 52)
http://cdn.procurve.com/training/Manuals/1800-MgmtCfg-June2007-59916275.pdf
Have you tried the full-blown factory reset? (page 52)
http://cdn.procurve.com/training/Manuals/1800-MgmtCfg-June2007-59916275.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 04:17 AM
тАО10-12-2009 04:17 AM
Re: Problems with ProCurve1800 after FW upgrade
That did the trick, thank you!
I actually tried the hard reset first, but it would not work.
For it to work I had to disable the multicast rate limit setting.
The setup on this switch really sucks, still with new firmware.
I actually tried the hard reset first, but it would not work.
For it to work I had to disable the multicast rate limit setting.
The setup on this switch really sucks, still with new firmware.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP