Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Procurve 2910 al - CX4 10G connectivity
Switches, Hubs, and Modems
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- OEM Solutions
- Servers: The Right Compute
- Shifting to Software-Defined
- Telecom IQ
- Transforming IT
- Infrastructure Solutions German
- L’Avenir de l’IT
- IT e Trasformazione Digitale
- Enterprise Topics
- ИТ для нового стиля бизнеса
- Blogs
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Forums
-
Blogs
-
InformationEnglish
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-21-2011 02:41 AM
02-21-2011 02:41 AM
Procurve 2910 al - CX4 10G connectivity
Hi,
I have two pro-curve switches (2910 al ) & each have two 10Gbe al interconnect modules (J9165A).
Can i use this ports to make 10Gbe connectivity with a storage device ???
Or am i need to get a 10Gbe cx4 al module (J9149A) installed on this switch.
Interconnect module have a CX4 port , but my doubt is does it support CX4 connectivity from other devices (p4500 storage)??
I tried to connect this port with storage & the port status was showing down ...
what can be the possible reason...
Regards
Prasanth
I have two pro-curve switches (2910 al ) & each have two 10Gbe al interconnect modules (J9165A).
Can i use this ports to make 10Gbe connectivity with a storage device ???
Or am i need to get a 10Gbe cx4 al module (J9149A) installed on this switch.
Interconnect module have a CX4 port , but my doubt is does it support CX4 connectivity from other devices (p4500 storage)??
I tried to connect this port with storage & the port status was showing down ...
what can be the possible reason...
Regards
Prasanth
1 REPLY
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-21-2011 04:53 PM
02-21-2011 04:53 PM
Re: Procurve 2910 al - CX4 10G connectivity
because interconnect kit cx4 modul support only 0,5m cable
out of action more than long cx4 cable
out of action more than long cx4 cable
cenk
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2019 Hewlett Packard Enterprise Development LP