Procurve 4000m restore Config help

[Mlchris2]

I recieved a working hp procurve 4000m and decided to use this as a spare in the event my production 4000m goes down. I have sucessfully obtained the config file from my production 4000m via TFTP and the PUT command.

Well I want to configure the spare 4000m with the config from my production 4000m. So I factory reset the spare switch and got it on the network. I proceeded to upload the config via TFTP and the GET command. The spare switch rebooted and I unplugged the network cable as to not cause major issues. The spare switch did not boot all the way... goes thru the initializing process it hangs at a prompt with a "white block" or "double tilde" and the cursor just flashes.

Any idea? Am I doing something wrong? My space 4000m has only a single 8-port 100/100 module and my production level as 9 x 8-port 10/100 modules and a single 1000-base FX module. Would this be causing the problem?

I sure would appreciate some insight.

[Jorge Pons]

Hi

First, revise both switches have same Firmware Version, and if its posiible, the last one.
after this, reset the new 4000 and test all is OK.
If you have specific configuration in ports that new 4000 hasnt, could be a warning, but it must boot.

Can you post config?

Regards, Jorge

[Mlchris2]

I am currently running C_09_13 on both switches. I upgraded the spare sitch to C_09_30 and will upgrade the production switch tonight.

Here is the config from the production switch;

----------------------

; J4121A Configuration Editor; Created on release #C.09.16

SYSTEM (
NAME=~hp4000m~
CONTACT=~Kingston Admin (admin@kingstoncorp.com)~
LOCATION=~Corporate Office Kingston Corp.~
CDP_ENABLE=1
RFILEs=~C_09_16.swi~
ADDR=192.168.100.135
TIMEZONE=420
DST_RULE=3
)

CONSOLE (
TTYPE=4
BAUDRATE=11
XON=1
)

CCT (
NAME=A1
PORT_ID=1
TYPE=62
)

CCT (
NAME=A2
PORT_ID=2
TYPE=62
)

CCT (
NAME=A3
PORT_ID=3
TYPE=62
)

CCT (
NAME=A4
PORT_ID=4
TYPE=62
)

CCT (
NAME=A5
PORT_ID=5
TYPE=62
)

CCT (
NAME=A6
PORT_ID=6
TYPE=62
)

CCT (
NAME=A7
PORT_ID=7
TYPE=62
)

CCT (
NAME=A8
PORT_ID=8
TYPE=62
)

CCT (
NAME=B1
PORT_ID=9
TYPE=62
)

CCT (
NAME=B2
PORT_ID=10
TYPE=62
)

CCT (
NAME=B3
PORT_ID=11
TYPE=62
)

CCT (
NAME=B4
PORT_ID=12
TYPE=62
)

CCT (
NAME=B5
PORT_ID=13
TYPE=62
)

CCT (
NAME=B6
PORT_ID=14
TYPE=62
)

CCT (
NAME=B7
PORT_ID=15
TYPE=62
)

CCT (
NAME=B8
PORT_ID=16
TYPE=62
)

CCT (
NAME=C1
PORT_ID=17
TYPE=62
)

CCT (
NAME=C2
PORT_ID=18
TYPE=62
)

CCT (
NAME=C3
PORT_ID=19
TYPE=62
)

CCT (
NAME=C4
PORT_ID=20
TYPE=62
)

CCT (
NAME=C5
PORT_ID=21
TYPE=62
)

CCT (
NAME=C6
PORT_ID=22
TYPE=62
)

CCT (
NAME=C7
PORT_ID=23
TYPE=62
)

CCT (
NAME=C8
PORT_ID=24
TYPE=62
)

CCT (
NAME=D1
PORT_ID=25
TYPE=62
)

CCT (
NAME=D2
PORT_ID=26
TYPE=62
)

CCT (
NAME=D3
PORT_ID=27
TYPE=62
)

CCT (
NAME=D4
PORT_ID=28
TYPE=62
)

CCT (
NAME=D5
PORT_ID=29
TYPE=62
)

CCT (
NAME=D6
PORT_ID=30
TYPE=62
)

CCT (
NAME=D7
PORT_ID=31
TYPE=62
)

CCT (
NAME=D8
PORT_ID=32
TYPE=62
)

CCT (
NAME=E1
PORT_ID=33
TYPE=62
)

CCT (
NAME=E2
PORT_ID=34
TYPE=62
)

CCT (
NAME=E3
PORT_ID=35
TYPE=62
)

CCT (
NAME=E4
PORT_ID=36
TYPE=62
)

CCT (
NAME=E5
PORT_ID=37
TYPE=62
)

CCT (
NAME=E6
PORT_ID=38
TYPE=62
)

CCT (
NAME=E7
PORT_ID=39
TYPE=62
)

CCT (
NAME=E8
PORT_ID=40
TYPE=62
)

CCT (
NAME=F1
PORT_ID=41
TYPE=62
)

CCT (
NAME=F2
PORT_ID=42
TYPE=62
)

CCT (
NAME=F3
PORT_ID=43
TYPE=62
)

CCT (
NAME=F4
PORT_ID=44
TYPE=62
)

CCT (
NAME=F5
PORT_ID=45
TYPE=62
)

CCT (
NAME=F6
PORT_ID=46
TYPE=62
)

CCT (
NAME=F7
PORT_ID=47
TYPE=62
)

CCT (
NAME=F8
PORT_ID=48
TYPE=62
)

CCT (
NAME=J1
PORT_ID=73
TYPE=62
)

CCT (
NAME=J2
PORT_ID=74
TYPE=62
)

CCT (
NAME=J3
PORT_ID=75
TYPE=62
)

CCT (
NAME=J4
PORT_ID=76
TYPE=62
)

CCT (
NAME=J5
PORT_ID=77
TYPE=62
)

CCT (
NAME=J6
PORT_ID=78
TYPE=62
)

CCT (
NAME=J7
PORT_ID=79
TYPE=62
)

CCT (
NAME=J8
PORT_ID=80
TYPE=62
)

CCT (
NAME=H1
PORT_ID=57
TYPE=62
)

CCT (
NAME=H2
PORT_ID=58
TYPE=62
)

CCT (
NAME=H3
PORT_ID=59
TYPE=62
)

CCT (
NAME=H4
PORT_ID=60
TYPE=62
)

CCT (
NAME=H5
PORT_ID=61
TYPE=62
)

CCT (
NAME=H6
PORT_ID=62
TYPE=62
)

CCT (
NAME=H7
PORT_ID=63
TYPE=62
)

CCT (
NAME=H8
PORT_ID=64
TYPE=62
)

CCT (
NAME=I1
PORT_ID=65
TYPE=62
)

CCT (
NAME=I2
PORT_ID=66
TYPE=62
)

CCT (
NAME=I3
PORT_ID=67
TYPE=62
)

CCT (
NAME=I4
PORT_ID=68
TYPE=62
)

CCT (
NAME=I5
PORT_ID=69
TYPE=62
)

CCT (
NAME=I6
PORT_ID=70
TYPE=62
)

CCT (
NAME=I7
PORT_ID=71
TYPE=62
)

CCT (
NAME=I8
PORT_ID=72
TYPE=62
)

CCT (
NAME=G1
PORT_ID=49
TYPE=117
ETHER100MODE=5
ETHER100MODE=5
)

STP (
)

IPX (

IPX_NW (
NODE_ADDR=000883fcc500
INIT=1
GW_ENCAP=5
)

IPX_NW (
VLAN_ID=2
NODE_ADDR=000883fcc501
INIT=1
GW_ENCAP=5
)

IPX_NW (
VLAN_ID=3
NODE_ADDR=000883fcc502
INIT=1
GW_ENCAP=5
)

IPX_NW (
VLAN_ID=4
NODE_ADDR=000883fcc503
INIT=1
GW_ENCAP=5
)

IPX_NW (
VLAN_ID=5
NODE_ADDR=000883fcc504
INIT=1
GW_ENCAP=5
)
)

IP (
TIME_SYNC=2
TIMEP=1
SNTP_STATE=2
IP_ADDR=192.168.100.3

SNTP (
ROW_STATUS=1
IP_ADDR=192.168.100.3
)

IP_NW (
INIT=1
ADDR=192.168.100.4
SNET_MSK=255.255.255.0
GATEWAY=192.168.100.1
)

IP_NW (
VLAN_ID=2
INIT=2
ADDR=0.0.0.0
SNET_MSK=0.0.0.0
GATEWAY=0.0.0.0
)

IP_NW (
VLAN_ID=3
INIT=3
ADDR=0.0.0.0
SNET_MSK=0.0.0.0
)

IP_NW (
VLAN_ID=4
INIT=3
ADDR=0.0.0.0
SNET_MSK=0.0.0.0
)

IP_NW (
VLAN_ID=5
INIT=2
ADDR=192.168.101.3
SNET_MSK=255.255.255.0
GATEWAY=192.168.101.1
)
)

SNMPS (
ROW_STATUS=1
NAME=public
VIEW=5
MODE=5
)

TRAPS (
)

VLAN (
NAME=DEFAULT_VLAN
PORT_MAP=ffffffffffff80ffffff0000
MODE=222222222222222222222222-222222222222222222222222-------222222222-------22222222
)

VLAN (
VLAN_ID=2
NAME=public
VLAN_QID=2
PORT_MAP=ffffffffffff80ffffff0000
MODE=------------------------------------------------1----------------22221--
)

VLAN (
VLAN_ID=3
NAME=Phones
VLAN_QID=3
PORT_MAP=ffffffffffff80ffffff0000
MODE=1111111111111111111111112111111111111111111111111-------111111111-------11111111
COS_PRIORITY=6
)

VLAN (
VLAN_ID=4
NAME=Wireless
VLAN_QID=4
PORT_MAP=ffffffffffff80ffffff0000
MODE=------------------------------------------------1---------------------22
)

VLAN (
VLAN_ID=5
NAME=Cameras
VLAN_QID=5
PORT_MAP=ffffffffffff80ffffff0000
MODE=------------------------------------------------1
)

PROBE (
INIT=2
PROBE_PORT=71
PROBE_TYPE=1
MONITORED_PORT_MASK=200000000000000000000000
)

IGMP (
)

IGMP (
VLAN_ID=2
)

IGMP (
VLAN_ID=3
)

IGMP (
VLAN_ID=4
)

IGMP (
VLAN_ID=5
)

ABC (

ABC_NW (
ABC_CONF=4
)

ABC_NW (
VLAN_ID=2
ABC_CONF=4
)

ABC_NW (
VLAN_ID=3
ABC_CONF=4
)

ABC_NW (
VLAN_ID=4
ABC_CONF=4
)

ABC_NW (
VLAN_ID=5
ABC_CONF=4
)
)

FAULT_FINDER (
FAULT_ID=1
)

FAULT_FINDER (
FAULT_ID=2
)

FAULT_FINDER (
FAULT_ID=3
)

FAULT_FINDER (
FAULT_ID=4
)

FAULT_FINDER (
FAULT_ID=5
)

FAULT_FINDER (
FAULT_ID=6
)

FAULT_FINDER (
FAULT_ID=11
)

GVRP (
GVRP_VLAN=8
)

COS_PROTO (
TYPE=1
)

COS_PROTO (
TYPE=2
)

COS_PROTO (
TYPE=3
)

COS_PROTO (
TYPE=4
)

COS_PROTO (
TYPE=5
)

COS_PROTO (
TYPE=6
)

COS_PROTO (
TYPE=7
)

COS_TOS (
TOS_MODE=2
)

COS_TOSDS (
REC_MASK=ffffffffffffffff00000000
)

HPDP (
)

STACK (
ADMIN_STATUS=4
STACK_NAME=Kingston
STACK_AUTO_GRAB=1

STACK_MEMBER (
MEMBER_ID=1
MEMBER_MACADDR=000883ec9800
ROW_STATUS=1
MEMBER_ADD_STATUS=2
)

STACK_MEMBER (
MEMBER_ID=2
MEMBER_MACADDR=000a57ec3f00
ROW_STATUS=1
MEMBER_ADD_STATUS=2
)

STACK_MEMBER (
MEMBER_ID=3
MEMBER_MACADDR=000e7f1ff380
ROW_STATUS=1
MEMBER_ADD_STATUS=2
)

STACK_MEMBER (
MEMBER_ID=4
MEMBER_MACADDR=00110a4f6ec0
ROW_STATUS=1
MEMBER_ADD_STATUS=2
)

STACK_MEMBER (
MEMBER_ID=5
MEMBER_MACADDR=001279849100
ROW_STATUS=1
MEMBER_ADD_STATUS=2
)
)

AUTHENTICATION (

AUTHEN_TASK (
AUTHEN_TASK_ID=1
)

AUTHEN_TASK (
AUTHEN_TASK_ID=2
)
)

TACACS (
)

----------------------------------

here is the config of the space switch

----------------------------------

; J4121A Configuration Editor; Created on release #C.09.30

SYSTEM (
NAME=~Kingston-6~
CDP_ENABLE=1
RFILEs=~C_09_30.swi~
ADDR=192.168.100.68
8021Q=0
DST_RULE=1
)

CONSOLE (
)

CCT (
NAME=A1
PORT_ID=1
TYPE=62
)

CCT (
NAME=A2
PORT_ID=2
TYPE=62
)

CCT (
NAME=A3
PORT_ID=3
TYPE=62
)

CCT (
NAME=A4
PORT_ID=4
TYPE=62
)

CCT (
NAME=A5
PORT_ID=5
TYPE=62
)

CCT (
NAME=A6
PORT_ID=6
TYPE=62
)

CCT (
NAME=A7
PORT_ID=7
TYPE=62
)

CCT (
NAME=A8
PORT_ID=8
TYPE=62
)

CCT (
NAME=B1
PORT_ID=9
TYPE=62
)

CCT (
NAME=B2
PORT_ID=10
TYPE=62
)

CCT (
NAME=B3
PORT_ID=11
TYPE=62
)

CCT (
NAME=B4
PORT_ID=12
TYPE=62
)

CCT (
NAME=B5
PORT_ID=13
TYPE=62
)

CCT (
NAME=B6
PORT_ID=14
TYPE=62
)

CCT (
NAME=B7
PORT_ID=15
TYPE=62
)

CCT (
NAME=B8
PORT_ID=16
TYPE=62
)

CCT (
NAME=C1
PORT_ID=17
TYPE=62
)

CCT (
NAME=C2
PORT_ID=18
TYPE=62
)

CCT (
NAME=C3
PORT_ID=19
TYPE=62
)

CCT (
NAME=C4
PORT_ID=20
TYPE=62
)

CCT (
NAME=C5
PORT_ID=21
TYPE=62
)

CCT (
NAME=C6
PORT_ID=22
TYPE=62
)

CCT (
NAME=C7
PORT_ID=23
TYPE=62
)

CCT (
NAME=C8
PORT_ID=24
TYPE=62
)

CCT (
NAME=D1
PORT_ID=25
TYPE=62
)

CCT (
NAME=D2
PORT_ID=26
TYPE=62
)

CCT (
NAME=D3
PORT_ID=27
TYPE=62
)

CCT (
NAME=D4
PORT_ID=28
TYPE=62
)

CCT (
NAME=D5
PORT_ID=29
TYPE=62
)

CCT (
NAME=D6
PORT_ID=30
TYPE=62
)

CCT (
NAME=D7
PORT_ID=31
TYPE=62
)

CCT (
NAME=D8
PORT_ID=32
TYPE=62
)

CCT (
NAME=E1
PORT_ID=33
TYPE=62
)

CCT (
NAME=E2
PORT_ID=34
TYPE=62
)

CCT (
NAME=E3
PORT_ID=35
TYPE=62
)

CCT (
NAME=E4
PORT_ID=36
TYPE=62
)

CCT (
NAME=E5
PORT_ID=37
TYPE=62
)

CCT (
NAME=E6
PORT_ID=38
TYPE=62
)

CCT (
NAME=E7
PORT_ID=39
TYPE=62
)

CCT (
NAME=E8
PORT_ID=40
TYPE=62
)

STP (
)

IPX (

IPX_NW (
NODE_ADDR=00088354e600
INIT=1
GW_ENCAP=5
)
)

IP (

IP_NW (
INIT=3
ADDR=0.0.0.0
SNET_MSK=0.0.0.0
)
)

SNMPS (
ROW_STATUS=1
NAME=public
VIEW=5
MODE=5
)

TRAPS (
)

VLAN (
NAME=DEFAULT_VLAN
PORT_MAP=ffffffffff00000000000000
MODE=2222222222222222222222222222222222222222
)

PROBE (
INIT=2
PROBE_TYPE=1
MONITORED_PORT_MASK=000000000000000000000000
)

IGMP (
)

ABC (

ABC_NW (
ABC_CONF=4
)
)

FAULT_FINDER (
FAULT_ID=1
)

FAULT_FINDER (
FAULT_ID=2
)

FAULT_FINDER (
FAULT_ID=3
)

FAULT_FINDER (
FAULT_ID=4
)

FAULT_FINDER (
FAULT_ID=5
)

FAULT_FINDER (
FAULT_ID=6
)

FAULT_FINDER (
FAULT_ID=11
)

GVRP (
GVRP_VLAN=8
)

COS_PROTO (
TYPE=1
)

COS_PROTO (
TYPE=2
)

COS_PROTO (
TYPE=3
)

COS_PROTO (
TYPE=4
)

COS_PROTO (
TYPE=5
)

COS_PROTO (
TYPE=6
)

COS_PROTO (
TYPE=7
)

COS_TOS (
TOS_MODE=1
)

COS_TOSDS (
REC_MASK=ffffffffffffffff00000000
)

HPDP (
)

STACK (
ADMIN_STATUS=3
MANAGER_MACADDR=000883fcc500
STACK_NAME=Kingston
STACK_AUTO_JOIN=2
STACK_JOIN_STATUS=2
)

AUTHENTICATION (

AUTHEN_TASK (
AUTHEN_TASK_ID=1
)

AUTHEN_TASK (
AUTHEN_TASK_ID=2
)
)

TACACS (
)

[Jorge Pons]

Hi

You have a large configuration, in this case you can use PCM (Procurve Manager) to take this config to install in new switch.

If your problems persists, talk with HP, this swithes have lifetime warranty.

Regards, Jorge

[Mlchris2]

I kinda figured it out... It was the config I was trying to upload. Im guessing something in the config causes the issue. I was able to clear out 90% of the config and upload it to the spare switch and it worked just fine.

[Jorge Pons]

HI Michris2

If it works, its a good notice.

Regards, Jorge