- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Procurve 5308 SNMP Messages and MIBS
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 04:03 AM
тАО06-11-2004 04:03 AM
Procurve 5308 SNMP Messages and MIBS
The Procurve is sending me "Generic Unregistered traps" with the following description:
Enterprise OID String. 1.3.6.1.4.1.11.2.14.12.1
Generic Trap ID. 6
Specific Trap ID. 5
It seems that the mibs for the Procurve are incomplete. This is not a HPSIM issue.
I downloaded and installed the MIBS from the following site: http://www.hp.com/rnd/software/MIBs.htm
I loaded pretty much all of them except for a couple which could not compile. I also downloaded several mibs that were prereqs and were missing from this package.
The MIBS that I was not able to compile and add to HPSIM are the following "rfc2863,
rfc2674_p, rfc2674_q, hc-rmon, hpicpiproute, hpicfxrrp, ieee8021pae, ieee8023lag, hp-sn-trap"
Anyone has had any success with this?
Thanks,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 08:14 AM
тАО06-11-2004 08:14 AM
Re: Procurve 5308 SNMP Messages and MIBS
If you open up hpicfipRoute.mib and add RowStatus.
So the top of that file should look like this:
HP-ICF-IP-ROUTING DEFINITIONS ::= BEGIN
IMPORT
OBJECT-TYPE, MODULE-IDENTITY, Integer32
FROM SNMPv2-SMI
PhysAddress, RowStatus
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 08:18 AM
тАО06-11-2004 08:18 AM
Re: Procurve 5308 SNMP Messages and MIBS
1 Bad Driver
2 Bad Transceiver
3 Bad Cable
4 Cable too long
5 Over Bandwidth
6 Broadcast Storm
7 Partition
8 Misconfigured
9 Polarity Reversal
10 Network Loop
11 Loss of Link
Hope that helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 08:46 AM
тАО06-11-2004 08:46 AM
Re: Procurve 5308 SNMP Messages and MIBS
The error itself doesnt really bother me. I see it on the switch itself and it is normal since its set to High Sensitivity. Our Toshiba laptops generate a lot of warning. They seem to have very low quality NIC cards.
For the hpicfiproute.mib, I did not see any trap definitions in it but it could always be the one I am missing.
I cannot import it into HPSIM, it seems to contain sintax errors.
This is what I get when I try to import it:
IMPORTING CFG hpicfiproute.cfg
Error: File 'hpicfiproute.cfg' Error reading MIB: MIB node has no parent Line: 105
AN ERROR OCCURRED EXECUTING THE COMMAND
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 09:11 AM
тАО06-11-2004 09:11 AM
Re: Procurve 5308 SNMP Messages and MIBS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2004 09:48 AM
тАО06-11-2004 09:48 AM
Re: Procurve 5308 SNMP Messages and MIBS
Is it possible that the file I have is incomplete?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2006 06:50 PM
тАО06-29-2006 06:50 PM
Re: Procurve 5308 SNMP Messages and MIBS
I too have had a similar import issue but think I have it sorted. Yes, you are correct - some files seem to be incomplete.
It looks like each OBJECT IDENTIFIER line of the cfg file defines an object using another object - which has to have already been defined itself.
For example, if you had:
lgpConTable OBJECT IDENTIFIER ::= { lgpConditions 3 }
...you would want to see an "lgpConditions OBJECT IDENTIFIER ::=" line somewhere before it.
I fixed my errors by opening other compiled MIBs (CFGs) that had loaded OK, found the definition line missing from my non-working CFG, then added it in just in front of the error line & re-import.
This sorted it out for me.
Hope this info helps.
Gareth.