- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- RX Drops
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2007 02:33 AM
тАО02-09-2007 02:33 AM
RX Drops
I have 2 x 4108g as my core switches. I have 2 cat 5 GB ports on each connected using the trk method. I have no lacp set on these ports and Im unsure if this makes any difference.
In one port I have a lot of RX Drops up 100 in a day.
I seen a post tp run MIB to get a more detailed error message. How would I go about this.
thanks
ROnnie
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2007 07:20 AM
тАО02-09-2007 07:20 AM
Re: RX Drops
Whats the port configuration, Speed and Duplex ?
Also, are you using CAT-5 or CAT-5E copper cables?
Attach the Show run here if you can after deleting any private information like IPs.
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2007 08:24 PM
тАО02-14-2007 08:24 PM
Re: RX Drops
Port config set to Auto-1000 on both sides of both ports.
Using CAT 5 cable so going to change this as my first test and monitor
Ron
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2007 08:26 PM
тАО02-14-2007 08:26 PM
Re: RX Drops
name "Uplink 1 to DC-4108g-1 Trk2"
speed-duplex auto-1000
no lacp
exit
interface C8
name "Uplink 2 to DC-4108g-1 Trk2"
speed-duplex auto-1000
no lacp
exit
set on the other switch the same
its the no lacp Im not sure about
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2007 09:27 PM
тАО02-14-2007 09:27 PM
Re: RX Drops
As far as i am aware you do not LACP enabled for this set up to work , as you are configuring a static trunk.