- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Saving routing table
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-30-2007 07:08 PM
тАО05-30-2007 07:08 PM
Re: Saving routing table
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-30-2007 11:37 PM
тАО05-30-2007 11:37 PM
Re: Saving routing table
We just restarted our switch and it went back again but this time i went and ran command "show config" it actually shows route entry but if i do show ip route it doesn't show route entry and it stops routing to external network.
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2007 02:02 AM
тАО05-31-2007 02:02 AM
Re: Saving routing table
Have you contacted HP support?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2007 02:20 AM
тАО05-31-2007 02:20 AM
Re: Saving routing table
In the past I've seen issues with SNMP trap destinations and how it would determine the trap-source based on the interface that came up first. A workaround for that was to change the port and disable passive lacp to ensure the port comes up quicker.
Right now I would recommend trying an older version firmware, if the problem is still there contact HP support with all the testing you have performed so far.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2007 11:38 PM
тАО05-31-2007 11:38 PM
Re: Saving routing table
They had taken my details but they have not called me back at(called this early in the morning and its 9:30pm)
Hope fully they going to come back with some solution
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2007 02:41 PM
тАО06-06-2007 02:41 PM
Re: Saving routing table
- « Previous
-
- 1
- 2
- Next »