- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Set 100full on procurve 2510-24
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2008 07:04 AM
тАО02-22-2008 07:04 AM
Set 100full on procurve 2510-24
The system permit us to set 100-auto, but not 100-full.
Anyone has the same problem?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2008 05:16 PM
тАО02-22-2008 05:16 PM
Re: Set 100full on procurve 2510-24
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-24-2008 11:59 PM
тАО02-24-2008 11:59 PM
Re: Set 100full on procurve 2510-24
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-25-2008 05:33 AM
тАО02-25-2008 05:33 AM
Re: Set 100full on procurve 2510-24
http://www.hp.com/rnd/software/j9019-q1107.htm
ProCurve Switch 2510-24(eth-3)# show ver
Image stamp: /sw/code/build/harp(bh2)
Oct 24 2007 15:00:35
Q.11.07
7136
Boot Image: Primary
ProCurve Switch 2510-24(config)# int 3
ProCurve Switch 2510-24(eth-3)# speed-duplex 100-full
ProCurve Switch 2510-24(eth-3)#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-25-2008 05:41 AM
тАО02-25-2008 05:41 AM
Re: Set 100full on procurve 2510-24
As long as both ends negotiate the same setting, or default to the same setting, I wouldn't hard-code any setting. If you set the printer to 100Full, eventually it will get plugged into a port that is trying to negotiate but the port will default to 100Half because the printer isn't participating in the negotiation. And mis-matched speed/duplex is much, much worse than 100Half vs. 100Full.
casevh