- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Switch 5308 snmp not-info
Switches, Hubs, and Modems
1748255
Members
3750
Online
108760
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-07-2003 09:11 PM
тАО12-07-2003 09:11 PM
Switch 5308 snmp not-info
Our switch 5308 is configured to send only snmp-traps not-info. But the switch ignores this setting and sends a link-up and a link-down snmp-trap whenever a user turns his computer on or off.
How can I disable these unnecessary traps?
Manfred Ernst
How can I disable these unnecessary traps?
Manfred Ernst
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-08-2003 02:59 AM
тАО12-08-2003 02:59 AM
Re: Switch 5308 snmp not-info
I had the same problem. Try this command from the config prompt in the CLI:
no fault-finder loss-of-link
Should fix your problem. If you use the command, you can also set all the fault traps to the values you desire. It's quite good to turn the lesser used stuff to a lower setting.
no fault-finder loss-of-link
Should fix your problem. If you use the
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-08-2003 06:23 AM
тАО12-08-2003 06:23 AM
Re: Switch 5308 snmp not-info
Ernst,
Supplemental to the above response, I believe you set your fault-finder to high sensitivity.
You might have done that using your web browser telling the system to log problems with High Sensitivity under Web Interface / Configuration / Fault Detection
Supplemental to the above response, I believe you set your fault-finder to high sensitivity.
You might have done that using your web browser telling the system to log problems with High Sensitivity under Web Interface / Configuration / Fault Detection
If a problem can be fixed, there's nothing to worry. If a problem can't be fixed, worrying ain't gonna help. Bottom line: don't worry.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP