- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Trunk between 9300 and 5300
Switches, Hubs, and Modems
1752800
Members
5456
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-10-2005 08:57 PM
тАО10-10-2005 08:57 PM
Trunk between 9300 and 5300
Hi Guys,
I have set up my PCM2.0+ now and run the network config report.
It reports errors on the trunk link between 9300 and 5300 switches.
I used the following commands to set up the trunks
9300 :
Trunk switch ethe 3/1 to 3/2
Trunk Deploy
5300:
trunk a1,a2 trk1 trunk
Is this the right way about it???
The network report is basically saying that the 9300 port is speed (1000000000) and the 5300 is speed (2000000000). and that the speed should be the same on both sides of the link.
I have set up my PCM2.0+ now and run the network config report.
It reports errors on the trunk link between 9300 and 5300 switches.
I used the following commands to set up the trunks
9300 :
Trunk switch ethe 3/1 to 3/2
Trunk Deploy
5300:
trunk a1,a2 trk1 trunk
Is this the right way about it???
The network report is basically saying that the 9300 port is speed (1000000000) and the 5300 is speed (2000000000). and that the speed should be the same on both sides of the link.
Where there is a will there is a way...
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2005 09:45 PM
тАО10-23-2005 09:45 PM
Re: Trunk between 9300 and 5300
Can you please attach the report file.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2005 07:35 PM
тАО10-26-2005 07:35 PM
Re: Trunk between 9300 and 5300
Hi here is the report, The first few lines show the error i am concerned with....
Cheers
Cheers
Where there is a will there is a way...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP