- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: VLAN - Access Pt 420 to Procurve 2610
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 01:19 PM
тАО08-12-2009 01:19 PM
VLAN - Access Pt 420 to Procurve 2610
vlan 1
name "DEFAULT_VLAN"
untagged 1,3-11,13-28
ip address 10.0.0.241 255.255.255.0
no untagged 2,12
exit
vlan 2
name "PublicVLAN"
untagged 2,12
ip address 10.2.0.1 255.255.255.0
ip helper-address 10.2.0.254
tagged 1,3
exit
If I plug into port 12 on the switch I get a correct IP address on the public access vlan. Same thing if I plug into other ports, I get a correct IP address on the default VLAN.
My issue with with the AP on port 1. I have it set to do 2 SSID's - 1 with vlan 1 untagged and 1 with vlan 2 untagged. However, no matter which SSID I connect to I always get connected to VLAN 1. Where am I going wrong?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 02:06 PM
тАО08-12-2009 02:06 PM
Re: VLAN - Access Pt 420 to Procurve 2610
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 08:19 PM
тАО08-12-2009 08:19 PM
Re: VLAN - Access Pt 420 to Procurve 2610
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 09:21 PM
тАО08-12-2009 09:21 PM
Re: VLAN - Access Pt 420 to Procurve 2610
You state you have the two SSIDs both as untagged. That would be your problem, then, if that were to actually be the case. There's no distinguishing between vlans without the tags.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 10:27 PM
тАО08-12-2009 10:27 PM
Re: VLAN - Access Pt 420 to Procurve 2610
vlan state must have enable
and
your dhcp server ip address 10.2.0.254 so this server resiade vlan 2 therefore no needed ip helper commans on vlan 2 ip helper command must have vlan 1
Vlan 1
name "DEFAULT_VLAN"
untagged 1,3-11,13-28
ip address 10.0.0.241 255.255.255.0
ip helper-address 10.2.0.254
no untagged 2,12
exit
vlan 2
name "PublicVLAN"
untagged 2,12
ip address 10.2.0.1 255.255.255.0
tagged 1,3
exit