- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- WOL edge 2650's
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2007 01:26 PM
тАО07-16-2007 01:26 PM
WOL edge 2650's
I have core 3750's cisco switches and 2950 cisco edge. We are now integrating 2650's as our edge instead of the ciscos.
My WOL works on the ciscos, but not on the hp's. Is there some sort of configuration i must do on the hp 2650's to set this up (pass through the magic packet)?
Config of 2650 is below:
; J4900B Configuration Editor; Created on release #H.10.38
hostname "Spare"
ip default-gateway 10.12.7.253
no timesync
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged 25-26
ip address 10.12.7.140 255.255.248.0
no untagged 1-24
exit
vlan 18
name "F_Centre"
untagged 5-22
tagged 25-26
exit
vlan 9
name "voice"
untagged 23-24
tagged 25-26
exit
vlan 40
name "Wireless"
untagged 1-4
tagged 25-26
exit
password manager
password operator
Thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2007 04:47 PM
тАО07-16-2007 04:47 PM
Re: WOL edge 2650's
Wake on LAN is a directed broadcast kind of traffic that the 2600 series doesn't forward by default.
A directed broadcast is an IP broadcast to all devices within a single directly attached
network or sub-net.
A net-directed broadcast goes to all devices on a given network.
A sub-net-directed broadcast goes to all devices within a given sub-net.
Forwarding for all types of IP directed broadcasts is disabled by default.
You can enable forwarding for all types if needed.
You cannot enable forwarding for specific broadcast types.
To enable forwarding of IP directed broadcasts, enter the following CLI
command:
HPswitch(config)# ip directed-broadcast
Check this, page 12:
ftp://ftp.hp.com/pub/networking/software/AdvTraff-Oct2005-59908853-Chap07-IProuting.pdf
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2007 10:16 PM
тАО07-16-2007 10:16 PM
Re: WOL edge 2650's
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2007 10:28 AM
тАО07-17-2007 10:28 AM
Re: WOL edge 2650's
Dave Krugar says your the guru Matt and should be able to fix everything :P
Any more ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2007 09:12 PM
тАО07-17-2007 09:12 PM
Re: WOL edge 2650's
Otherwise if you could attach the config of the core routers and that of the 2950's, I'm sure someone here could at least verify that the config that's running the 2600's does match the 3750's. I assume it is correct since it sounds like everything else is working.