- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: What HP switches work w/IBM cable
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2003 05:23 AM
тАО04-08-2003 05:23 AM
What HP switches work w/IBM cable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2003 06:48 AM
тАО04-08-2003 06:48 AM
Re: What HP switches work w/IBM cable
There's nothing special in 2524 to handle that... just enable STP, that should do the trick on any switch.
HTH,
Arimo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2003 10:22 PM
тАО04-08-2003 10:22 PM
Re: What HP switches work w/IBM cable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-15-2003 12:45 AM
тАО04-15-2003 12:45 AM
Re: What HP switches work w/IBM cable
Strictly speaking HP does NOT support IBM Type I Cabling (150 Ohm) , only 100 Ohm UTP or STP. However you can make it to work when
indead using Balloons which convert the 150 Ohm impedance to 100 Ohm.
Depending on the type of balloons used this works or not as not all balloons are equal. Requirement is that the balloons must be
marketed as 10/100 Balloons.
Furthermore HP is willing to support IBM Type I cabling when:
Using a Cat-5 cable tester to test the Type 1 cable (and baluns, and patch cables, etc) from the end that connects to the ProCurve switch to the end that connects to the remote device. If that combination of cables/adapters performs according to Cat-5 specifications, then HP will support it. If it does not perform according to Cat-5 specifications, then the customer should expect that cabling to cause problems when used with
any 10/100Base-T equipment.
The same story applies to other exotic cabling.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-15-2003 06:46 AM
тАО04-15-2003 06:46 AM
Re: What HP switches work w/IBM cable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2003 04:33 AM
тАО04-16-2003 04:33 AM
Re: What HP switches work w/IBM cable
If the switch doesn't support RSTP, that's no problem... as the workaround only works with STP, not with RSTP.
Arimo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-16-2003 05:07 AM
тАО04-16-2003 05:07 AM