- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- XL Access Controller Module not connecting
Switches, Hubs, and Modems
1752797
Members
5696
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-07-2007 07:28 AM
тАО04-07-2007 07:28 AM
XL Access Controller Module not connecting
I've recently installed an XL Access Controller module in one of my 5300 switches.
Module has been configured with an IP address and pointed to my HP 740 Access Control Manager with the correct shared secret.
However the ACM never connects to the 740.
In the log on the 740 I have the following messages from the ACM's IP address.
received CLI status change 6 from for session 2
process_incoming_cli_cmd sess=2
received CLI status change 7 from for session 2
Firmware on the switch is 10.55
Firmware on the 740 is 4.5.0.39
Any ideas is greatly appreciated.
Thanks
Module has been configured with an IP address and pointed to my HP 740 Access Control Manager with the correct shared secret.
However the ACM never connects to the 740.
In the log on the 740 I have the following messages from the ACM's IP address.
received CLI status change 6 from for session 2
process_incoming_cli_cmd sess=2
received CLI status change 7 from for session 2
Firmware on the switch is 10.55
Firmware on the 740 is 4.5.0.39
Any ideas is greatly appreciated.
Thanks
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-17-2007 02:04 AM
тАО04-17-2007 02:04 AM
Re: XL Access Controller Module not connecting
make sure that both firmwares on the ACS and AC are the same, the shared seret and the IP's.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-27-2007 08:43 AM
тАО04-27-2007 08:43 AM
Re: XL Access Controller Module not connecting
Hi,
I've heard that 4.5.0.39 firmware cause many different both connection and operating problems. I experienced that XL module can suddenly hang and the clients drop connection. You need to reload XL module to make it work again. Sometimes it comes back and work for sometimes without problems. But sometimes the module after reboot can not connect to ACS. Resently it tool one and a half day before suddenly XL module managed to make a connection. I checked the ping accross the system and firewall. The ping is getting through but XL module still has "NO connected" in status.
I've been advised to downgrade the system to 4.1.4.4 firmware which is more stabile than 4.5.0.39.
I've heard that 4.5.0.39 firmware cause many different both connection and operating problems. I experienced that XL module can suddenly hang and the clients drop connection. You need to reload XL module to make it work again. Sometimes it comes back and work for sometimes without problems. But sometimes the module after reboot can not connect to ACS. Resently it tool one and a half day before suddenly XL module managed to make a connection. I checked the ping accross the system and firewall. The ping is getting through but XL module still has "NO connected" in status.
I've been advised to downgrade the system to 4.1.4.4 firmware which is more stabile than 4.5.0.39.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP