- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- opinions?
Switches, Hubs, and Modems
1752786
Members
5878
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-15-2008 05:21 AM
02-15-2008 05:21 AM
opinions?
We have a ProCurve 2824 switch. Everytime my computer boots, the switch reports errors on the port that only my computer is connected to. After boot up, no errors are reported until I boot the computer again. My computer says the connection is 1.0 gbps and I never have any problems with the network connections (that I know of!).
These same 4 errors are reported everytime I boot up:
excessive late collisions
excessive broadcasts
excessive jabbering
excessive CRC/Alignment errors
I am just looking for someone else's opinion of what might be causing this. I've been thinking that it's probably the network cabling that was installed long before gigabit ethernet was even thought of being possible. But, just wondering if anyone else has run into anything similar.
Thanks for any information!
These same 4 errors are reported everytime I boot up:
excessive late collisions
excessive broadcasts
excessive jabbering
excessive CRC/Alignment errors
I am just looking for someone else's opinion of what might be causing this. I've been thinking that it's probably the network cabling that was installed long before gigabit ethernet was even thought of being possible. But, just wondering if anyone else has run into anything similar.
Thanks for any information!
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-11-2008 10:31 AM
04-11-2008 10:31 AM
Re: opinions?
hi Bryan
this procurve switch eror reported primary cause bad utp cabling or bad nic.
please you pc test 3meter pachcord connect same port switch and test and you must be look switch log you see same eror then please change your ethernet card
utp cable installation later must be needed professional test
1-wire map test
2-netx test
3-psnext test
4-elfex test
5-pselfex
6-acr
7-pcacr
8-return loss
as for me you utp cable under hight crosstalk
effect may be cablejoint or cable way near hight electrical enviroment
good luck
this procurve switch eror reported primary cause bad utp cabling or bad nic.
please you pc test 3meter pachcord connect same port switch and test and you must be look switch log you see same eror then please change your ethernet card
utp cable installation later must be needed professional test
1-wire map test
2-netx test
3-psnext test
4-elfex test
5-pselfex
6-acr
7-pcacr
8-return loss
as for me you utp cable under hight crosstalk
effect may be cablejoint or cable way near hight electrical enviroment
good luck
cenk
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP