- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- procurve 2524 unknown error message on log buffer
Switches, Hubs, and Modems
1753400
Members
7577
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-14-2004 01:02 AM
тАО04-14-2004 01:02 AM
Anyone have idea about the meaning of the following error message I found in the buffer log os several hp procurve 2524 firmware version 5.17 ?
W 04/13/04 14:53:33 FFI: port 16-High collision or drop rate.
Note: The error message has been logged for all the port 1 to 24 whitin just 1 second.
In the mean time all user connected to the switch expirieced network poor connectione, excessive network latecy/delay comparing to normal working condition.
I looked for error message guide but I didn't find anything neither on the web nor the manual o kb.
Thank a lot.
Best regards, Fabio
W 04/13/04 14:53:33 FFI: port 16-High collision or drop rate.
Note: The error message has been logged for all the port 1 to 24 whitin just 1 second.
In the mean time all user connected to the switch expirieced network poor connectione, excessive network latecy/delay comparing to normal working condition.
I looked for error message guide but I didn't find anything neither on the web nor the manual o kb.
Thank a lot.
Best regards, Fabio
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-14-2004 04:08 AM
тАО04-14-2004 04:08 AM
Solution
Hello Fabio -
The Help screen for the menu Event Log has this:
"High collision or drop rate
---------------------------------
Description: A large number of collisions or packet drops have occurred
on the port.
Possible Causes: An extremely high level of traffic on this port,
half/full duplex mismatch, a misconfigured or malfunctioning NIC or
transceiver on a device connected to this port, or a topology loop
in the network.
Actions:
1. Use a network monitoring device or application to determine the
traffic levels on the affected segment. If needed, consider
subdividing that segment with switches or bridges, or moving
high-traffic devices to their own switch ports.
2. Check the directly-connected device for mismatches in half/full
duplex operation (half duplex on the switch and full duplex on the
connected device).
3. Check for a misconfigured NIC or transceiver (such as a transceiver
configured for "loopback test" or "SQE test").
4. Verify that there are no topology loops in your network. If not
enabled, you may also enable spanning tree - see the Switch
Configuration menu."
Regards,
Ralph
The Help screen for the menu Event Log has this:
"High collision or drop rate
---------------------------------
Description: A large number of collisions or packet drops have occurred
on the port.
Possible Causes: An extremely high level of traffic on this port,
half/full duplex mismatch, a misconfigured or malfunctioning NIC or
transceiver on a device connected to this port, or a topology loop
in the network.
Actions:
1. Use a network monitoring device or application to determine the
traffic levels on the affected segment. If needed, consider
subdividing that segment with switches or bridges, or moving
high-traffic devices to their own switch ports.
2. Check the directly-connected device for mismatches in half/full
duplex operation (half duplex on the switch and full duplex on the
connected device).
3. Check for a misconfigured NIC or transceiver (such as a transceiver
configured for "loopback test" or "SQE test").
4. Verify that there are no topology loops in your network. If not
enabled, you may also enable spanning tree - see the Switch
Configuration menu."
Regards,
Ralph
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2004 08:05 PM
тАО04-18-2004 08:05 PM
Re: procurve 2524 unknown error message on log buffer
Fabio,
Version F.05.22 of the firmware for HP2524 is available, to replace F.05.17.
http://ftp.hp.com/pub/networking/software/J4812522.zip
Version F.05.22 of the firmware for HP2524 is available, to replace F.05.17.
http://ftp.hp.com/pub/networking/software/J4812522.zip
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP