- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- setup trunk beween 2848 and HP GbE2c Ethernet Blad...
Switches, Hubs, and Modems
1753512
Members
4943
Online
108795
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-27-2009 12:14 PM
01-27-2009 12:14 PM
setup trunk beween 2848 and HP GbE2c Ethernet Blade Switch
What is the command syntax to setup a trunk between GbE2c Ethernet and a 2828?
"trunk 45-46 Trk1 trunk" is the command for the 2828 I have STP enabled on the 2848 switch.
Hope somebody give me some input.
"trunk 45-46 Trk1 trunk" is the command for the 2828 I have STP enabled on the 2848 switch.
Hope somebody give me some input.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-27-2009 04:19 PM
01-27-2009 04:19 PM
Re: setup trunk beween 2848 and HP GbE2c Ethernet Blade Switch
Take a look at the section titled "Ports and Trunking" in the GbE2c Application Guide (Doc Part number: 418119-003). Here is the URL: http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c00701973/c00701973.pdf
There are examples on pg 33 for CLI syntax. The STP rules will change when you enable the trunk group on the GbE2c.
Note: There will be some STP considerations based on how you have deployed STP on the ProCurve and the rest of your network.
There are examples on pg 33 for CLI syntax. The STP rules will change when you enable the trunk group on the GbE2c.
Note: There will be some STP considerations based on how you have deployed STP on the ProCurve and the rest of your network.
---------------------------------------------
I work for HP, but my posts and replies are my own.
I work for HP, but my posts and replies are my own.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP