- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- software update from PCM+ 1.6 to switches does not...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 11:31 PM
тАО08-02-2005 11:31 PM
software update from PCM+ 1.6 to switches does not work
;-)
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2005 01:07 AM
тАО08-03-2005 01:07 AM
Re: software update from PCM+ 1.6 to switches does not work
How many switches are there to update? I prefer to telnet to them and use the COPY TFTP command.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2005 01:50 AM
тАО08-03-2005 01:50 AM
Re: software update from PCM+ 1.6 to switches does not work
Try using the CLI wizard or the Config Manager, if that works then you can eliminate Telnet issue.
What device are you trying to update?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 03:57 AM
тАО08-08-2005 03:57 AM
Re: software update from PCM+ 1.6 to switches does not work
< 10.1.1.91=""> Failed>
CLI Timeout: CLI Timeout: Termination Prompt not found
This happend on all Switches. The Management Station is autorized. The username in Perference is empty only the passwort is set.
Do you meen kill the telnet session on PCM System?
Today I update the Software manually with COPY TFTP.
But I need a solution for this problem, more for the CLI Wizard then for the software update.
;-))
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 03:03 PM
тАО08-08-2005 03:03 PM
Re: software update from PCM+ 1.6 to switches does not work
If it fails on all 12 switches, I doubt it is hung telnet sessions at all the switches. I only mentioned the hung sessions in case you were only testing on one or two switches and perhaps inadvertently left a telnet session without logging off. I know, because it happened to me. IIRC, the hung sessions will clear themselves given time.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 06:02 PM
тАО08-08-2005 06:02 PM
Re: software update from PCM+ 1.6 to switches does not work
Try going to a specific device and manually setting the telnet password, leave the user blank blank.
Then quickly try the CLI wizard.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 08:54 PM
тАО08-08-2005 08:54 PM
Re: software update from PCM+ 1.6 to switches does not work
yes the telnet password is on all switches the same. This problem is still happened after reboot the switches (powerless).
Is there a cmd to see telnet sessions and the status?
;-)
Stefan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 09:28 PM
тАО08-08-2005 09:28 PM
Re: software update from PCM+ 1.6 to switches does not work
Because all PCM does really is to call Telnet.exe.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2005 09:29 PM
тАО08-08-2005 09:29 PM
Re: software update from PCM+ 1.6 to switches does not work
So in other words make sure it is on command line.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2005 01:37 AM
тАО08-09-2005 01:37 AM
Re: software update from PCM+ 1.6 to switches does not work
thanks to anyone who replies. Yes the problem was the "logon default". It must be "CLI" not "menu"
;-)
Stefan Wusowski