System Administration
cancel
Showing results for 
Search instead for 
Did you mean: 

1000Base-SX Adapter not enabled

Narendra Uttekar
Regular Advisor

1000Base-SX Adapter not enabled

Hi,
When i do the ioscan -fnClan i am not able to see the 1000Base-SX Adapter on the system.
But the adapter is installed on the system. I have installed the driver also as below,
GigEther-00 B.11.11.19 PCI/HSC GigEther;Supptd HW=A4926A/A4929A/A4924A/A4925A;SW=J1642AA
And also configured the /etc/rc.config.d/hpgelanconf still i am not able to see the adapter. I want to know how to find whether this adapter is disabled on the system so that i can enabled the same or it could be the bad adapter and need replacement?

Thanks,
Narendra
3 REPLIES
Prasanth V Aravind
Trusted Contributor

Re: 1000Base-SX Adapter not enabled

what is lansacn output ?
what "rad -q" showing ?


Narendra Uttekar
Regular Advisor

Re: 1000Base-SX Adapter not enabled

Hi,
Please finf the output as below,
hostname:[/]# rad -q
Driver(s)
Slot Path Bus Max Spd Pwr Occu Susp Capable Max Mode
Num Spd Mode
1 0/5/0 40 N/A 33 On No N/A N/A N/A N/A
2 0/4/0 32 N/A 33 On No N/A N/A N/A N/A
3 0/12/0 96 N/A 66 On Yes No Yes N/A N/A
4 0/8/0 64 N/A 66 On Yes No Yes N/A N/A
5 0/10/0 80 N/A 33 On No N/A N/A N/A N/A
6 0/2/0 16 N/A 33 On Yes No Yes N/A N/A
7 1/12/0 224 N/A 33 On No N/A N/A N/A N/A
8 1/10/0 208 N/A 33 On No N/A N/A N/A N/A
9 1/4/0 160 N/A 33 On No N/A N/A N/A N/A
10 1/2/0 144 N/A 66 On Yes No Yes N/A N/A
11 1/8/0 192 N/A 66 On Yes No Yes N/A N/A
12 1/0/0 128 N/A 33 On Yes No Yes N/A N/A

hostname:[/]# lanscan
Hardware Station Crd Hdw Net-Interface NM MAC HP-DLPI DLPI
Path Address In# State NamePPA ID Type Support Mjr#
0/0/0/0 0x001083FF190B 0 UP lan0 snap0 1 ETHER Yes 119
1/0/0/0/4/0 0x001083F70BEC 1 UP lan1 snap1 2 ETHER Yes 119
1/0/0/0/5/0 0x001083F7EAF7 2 UP lan2 snap2 3 ETHER Yes 119
1/0/0/0/6/0 0x001083F7DA92 3 UP lan3 snap3 4 ETHER Yes 119
1/0/0/0/7/0 0x001083F7DA65 4 UP lan4 snap4 5 ETHER Yes 119
rick jones
Honored Contributor

Re: 1000Base-SX Adapter not enabled

If the adaptor does not appear in ioscan (you might drop the Clan part on the off chance the card is in a state where its class cannot be determined) it suggests that either the card is dead, or it is not seated correctly in the slot, or perhaps even that the I/O slot is dead.

Into what sort of system are you inserting the card?
there is no rest for the wicked yet the virtuous have no pillows