- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: 2564B compresses vertical spacing after reset
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2002 06:41 AM - last edited on тАО11-20-2012 10:06 PM by Maiko-I
тАО05-10-2002 06:41 AM - last edited on тАО11-20-2012 10:06 PM by Maiko-I
2564B compresses vertical spacing after reset
Hello,
We have a 2564B printer reset recently by lpadmin command and have problems with form letters. It seems
in compressed mode and form letters do not fit
in the envelope's window.
Some vertical spacing lines were lost. How can we reset the printer?
P.S. This thread has been moved from MPE/iX > Printers/Spooler Management to HP-UX > sysadmin - HP Forums Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2002 07:27 AM
тАО05-10-2002 07:27 AM
Re: 2564B compresses vertical spacing after reset
"lpadmin" sounds like hpux? This forum is MPE. Perhaps you'd have better luck in the hpux forum?
You can send PCL commands to the printer to change pitch (CPI) and also vertical line spacing, or you can use the LPI ADJ button on the printer to select LinesPerInch (for vertical spacing), and set
*** correction!!***
FUNCTION #1 (20 is serial config)
Function #1 with a primary character set for pitch (print a self test, and use the numbers on the far left of the samples).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2002 07:36 AM
тАО05-10-2002 07:36 AM
Re: 2564B compresses vertical spacing after reset
Cycling power will set the standard VFC's. Then, I would redo the set top of form procedure to ensure the right point of reference. Then, I would check the vertical line spacing in the control panel (6 or 8 LPI) in the LPI adjust mode. While in the control panel, I would check the primary character set selection (Function 1 in the control panel...probably should be 0 or 1). There is a setting for compression using the VFC but I am not good with escape sequences and the VFC.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2002 07:39 AM
тАО05-10-2002 07:39 AM
Re: 2564B compresses vertical spacing after reset
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-10-2002 07:42 AM
тАО05-10-2002 07:42 AM
Re: 2564B compresses vertical spacing after reset
no apology necessary, except from me!
(Thanks for correcting my error with F20)