- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: APA errno = 219
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2009 07:53 AM
тАО04-08-2009 07:53 AM
APA errno = 219
I'm getting the following error while appling lanapplyconf
ERROR: APA could not set LM Configuration for Fail-Over Group lan901. APA errno = 219.
ERROR: Creating Fail-Over Group failed lan901
Both the NIC is 100FD. and the ascii file contaains:
FAILOVER_GROUP lan901
STATIONARY_IP 138.35.254.64
PRIMARY lan1 5
STANDBY lan2 3
and hp_apaportconf file contains
HP_APAPORT_INTERFACE_NAME[0]=lan1
HP_APAPORT_CONFIG_MODE[0]=LAN_MONITOR
HP_APAPORT_INTERFACE_NAME[1]=lan2
HP_APAPORT_CONFIG_MODE[1]=LAN_MONITOR
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2009 08:08 AM
тАО04-08-2009 08:08 AM
Re: APA errno = 219
ifconfig lan1 down
ifconfig lan1 unplumb
ifconfig lan2 down
ifconfig lan2 unplumb
then
lanapplyconf
make sure, if you are coming in thru lan1 or lan2 via ssh (or god forbid telnet) your connection will die. So, it is best doing such configuration from the system console.
Hope this helps.
Mel
UNIX because I majored in cryptology...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2009 08:10 AM
тАО04-08-2009 08:10 AM
Re: APA errno = 219
try to unplumb the lan2 first, and restart the lanapplyconf
look at this thread
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=971054
Hope it helps
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2009 09:13 AM
тАО04-08-2009 09:13 AM
Re: APA errno = 219
But once you make lan2 plumb and then apply lanapplyconf .We are getting fresh error stating:
Reading ASCII file /etc/lanmon/lanconfig.ascii
STANDBY port lan2 has an IP address configured, Fail-Over Group lan901 will not be configured
Exiting: Error verifying input file /etc/lanmon/lanconfig.ascii
# netstat -in
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Coll
lan2 1500 none none 0 0 0 0 0
lan1 1500 138.35.254.0 138.35.254.64 22452428 554 31485697 0 0
lo0 4136 127.0.0.0 127.0.0.1 325511 0 325511 0 0
# ifconfig lan2
lan2: flags=843
inet 0.0.0.0 netmask 0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-08-2009 06:54 PM
тАО04-08-2009 06:54 PM
Re: APA errno = 219
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2009 02:50 PM
тАО06-08-2009 02:50 PM
Re: APA errno = 219
Literally followed the example for creating a Failover Group off of page 107 of the HP-UX 11iv1 Admin Guide - only the IP is different.