- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Re: Alpha DS-20 Installation Problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-18-2005 07:48 PM
тАО06-18-2005 07:48 PM
We are trying to install Compaq TRU64 Version 3.0,4.0D,5.0 on alpha Server DS-20 while installation it gives the following Error.
BootStrap Address Collision,Image Loading aborted
Halted CPU 0
HaltCode = 5
Halt Instruction executed
PC=200104f0
Firmware Version is 6.3-1
Can anybody help me to sortout this issue .
Regds
Dhananjay
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-18-2005 09:39 PM
тАО06-18-2005 09:39 PM
SolutionIn console mode look for
P00>>>show console_memory_allocation
To work around the bootstrap address collision do:
P00>>>set console_memory_allocation old
For more detail check:
h30097.www3.hp.com/docs/patch/50/bl15/ReleaseNotes.pdf
__ Johan
_JB_
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-18-2005 11:06 PM
тАО06-18-2005 11:06 PM
Re: Alpha DS-20 Installation Problem
Thanks for quick response,Problem Has been solved ,I am very new to this. Now I have completed the installation.
I have two disk in my system dsk0 and dsk1( 18gb each)in dsk 0 I have createed three partition i.e. a,b and g each 1 gb ,now I want to create three more partitions on the same disk but it is now allowing me to do that .it gives overlapping error.
So how to make partitions ...pls help me
Thanks & regards
Dhananjay
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-19-2005 10:09 AM
тАО06-19-2005 10:09 AM
Re: Alpha DS-20 Installation Problem
you can change non open partition by disklabel -e dsk0
Partitions do have an offset and a length and are not allowed to overlap, otherwise the data would be corrupted.
You are using a,b and g so far.
You could adjust parition d or e
The usual disk label has 8 oartitions from a-h.
You can see them with disklabel -r dsk0 for example.
greetings,
Michael
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-24-2005 09:07 PM
тАО07-24-2005 09:07 PM
Re: Alpha DS-20 Installation Problem
Have a look into the hardware compatibility list of the ds20.